Home › MAINTENANCE › MAINTENANCE › CHASSIS

CHASSIS > GENERAL MAINTENANCE



1. INSPECT STEERING LINKAGE & GEAR HOUSING
  1. Check the steering wheel free play (Click here).

  1. Check the steering linkage for looseness or damage.

    1. Check that the tie rod ends do not have excessive play.

    2. Check that the dust seals and boots are not damaged.

    3. Check that the boot clamps are not loose.

    4. Check that the steering gear housing is not damaged.

    5. Check that the connectors are properly connected to the steering gear housing.



2. INSPECT STEERING GEAR HOUSING OIL
  1. Check for steering gear housing oil leakage.
    If leakage is found, check and repair the cause.



3. INSPECT BALL JOINT AND DUST COVER
  1. Inspect the ball joints for excessive looseness.

    1. Jack up the front of the vehicle and place wooden blocks with a height of 180 to 200 mm (7.09 to 7.87 in.) under the front tires.

    2. Lower the vehicle until the front coil spring has about half its ordinary load. Place stands under the vehicle for safety.

    3. Check that the front wheels are pointing straight ahead. Use wheel chocks on all 4 wheels.

    4. Using a lever, pry up the end of the lower arm. Check the amount of play.

      Maximum ball joint vertical play:
      0 mm (0 in.)

      If there is any play, replace the ball joint.

  1. Check the dust cover for damage.



4. INSPECT DRIVE SHAFT BOOTS (for 4WD)
  1. Check the drive shaft boots for loose clamps, grease leakage, kinks or damage.



5. CHECK AUTOMATIC TRANSMISSION FLUID
  1. Visually check the transmission for fluid leakage. If oil is leaking, find the cause and repair it.
    Type
    See procedures
    A750E
    Click here
    A750F
    Click here
    AB60F
    Click here
    AB60E
    Click here



6. INSPECT TRANSFER OIL (for 4WD)
  1. Remove the filler plug and gasket.



    C083746E08
  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the filler plug hole.
    If the result is not as specified, add transfer oil.

    Oil grade:
    GL-4 or GL-5

    Viscosity:
    SAE 75W-90

    Standard capacity:
    1.1 +/- 0.06 liters (1.2 +/- 0.06 US qts, 1.0 +/- 0.05 Imp. qts)

    NOTICE:
    1. After changing the oil, drive the vehicle and check the oil level again.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leak.

  1. Install a new gasket into the filler plug and then tighten the plug.



7. INSPECT FRONT DIFFERENTIAL OIL (for 4WD) AND REAR DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil type:
    Item
    Oil type and viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front differential capacity:
    Specified Condition
    2.05 to 2.15 liters (2.2 to 2.3 US qts., 1.8 to 1.9 Imp. qts.)


    Rear differential capacity:

    Engine type
    Wheelbase type
    Cab type
    Drive type
    Specified Condition
    3UR-FE. 3UR-FBE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    3.40 to 3.50 liters (3.6 to 3.7 US qts., 3.0 to 3.1 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    Regular
    2WD
    3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.)
    4WD
    Double
    2WD
    4WD
    CrewMax
    2WD
    3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.)
    4WD
    3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.)
    4180 mm (13 ft. 8.6 in.)
    Double
    2WD
    3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.)
    4WD
    1GR-FE and 2UZ-FE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    4.00 to 4.10 liters (4.2 to 4.3 US qts., 3.5 to 3.6 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    ALL
    2WD
    4.55 to 4.65 liters (4.8 to 4.9 US qts., 4.0 to 4.1 Imp. qts.)
    4WD
    4180 mm (13 ft. 8.6 in.)
    2WD
    4WD

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }



8. LUBRICATE PROPELLER SHAFT (4WD ONLY) AND TIGHTEN BOLTS


  1. for 4WD:
    Lubricate the propeller shaft by referring to the lubrication chart. Before pumping in grease, wipe off any mud and dust on the grease fitting.
    Item
    Grease Grade
    Propeller Shaft Spider
    Lithium base chassis grease NLGI No. 2



    1. for Front propeller shaft


      C158565E01



    2. for Rear propeller shaft


      C158514E01



      C160963E01

  1. Tighten the bolts of the propeller shaft.
    Type
    See procedures
    2WD
    Click here
    4WD
    Click here



9. ROTATE TIRES


C195151E01

HINT:
Rotate the tires as shown in the illustration.