Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0724    Brake Switch "B" Circuit High

for Preparation Click here


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling when brakes are suddenly applied while driving in lock-up condition.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code
DTC Detection Condition
Trouble Area
P0724
Stop light switch remains ON even when vehicle repeats 5 cycles of STOP (less than 1.86 mph [3 km/h]) and GO (18.65 mph [30 km/h] or more) (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during "stop and go" driving, the ECM interprets this as a fault in the stop light switch and the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 1.86 mph [3 km/h]) and go (18.65 mph [30 km/h] or more) 5 times during 2 driving cycles, in order to detect a malfunction.

MONITOR STRATEGY


Related DTCs
P0724: Stop light switch/Range check/Rationality
Required sensors/Components (Main)
Stop light switch
Required sensors/Components (Related)
Speed sensor
Frequency of Operation
Continuous
Duration
5 times
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS

The stop light switch remains ON during GO and STOP 5 times.

GO and STOP are defined as follows; 
Monitor runs whenever following DTCs not present
None
GO: Vehicle speed
18.65 mph (30 km/h) or more
STOP: Vehicle speed
Less than 1.86 mph (3 km/h)

TYPICAL MALFUNCTION THRESHOLDS


Stop light switch status
Stuck ON

WIRING DIAGRAM

Refer to DTC P0504 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch.

  1. Read the values displayed on the Techstream.


OK:

Tester Display
Measurement Item/ Range (display)
Normal Condition
Diagnostic Note
Stop Light Switch
Stop light switch status/
ON or OFF
  1. ON: Brake pedal is depressed
  2. OFF: Brake pedal is released
-



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
A115657E09
  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)


    A107923E05
  1. Disconnect the A4 stop light switch connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A24-36 (STP) - A4-1
    Always
    Below 1 Ω
    A24-35 (ST1-) - A4-4
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A24-36 (STP) or A4-1 - Body ground
    Always
    10 kΩ or higher
    A24-35 (ST1-) or A4-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)