Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear Side)

ULTRASONIC SENSOR (for Rear Side) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER


    E146471E01
  1. Align the keyhole and protrusion as shown in the illustration.

  1. Install the sensor retainer to the rear bumper.

    NOTICE:
    Do not damage the bumper with the protrusion when installing the retainer.



2. INSTALL NO. 1 ULTRASONIC SENSOR


    E146472
  1. Attach the 2 claws to install the ultrasonic sensor.



3. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER


    E146473E01
  1. Align the keyhole and protrusion as shown in the illustration.

  1. Install the sensor retainer to the rear bumper.

    NOTICE:
    Do not damage the bumper with the protrusion when installing the retainer.



4. INSTALL NO. 2 ULTRASONIC SENSOR


    E146466
  1. Attach the 2 claws to install the ultrasonic sensor.



5. INSTALL REAR BUMPER BAR


  1. w/o Fog Light:
    Install the front bumper bar.

    1. w/ Intuitive Parking Assist System:
      Connect the ultrasonic sensor connectors.



    2. Install the bumper bar with the 8 bolts and 7 screws.

      Torque:
      for bolt:
      32 N*m{ 326 kgf*cm , 24 ft.*lbf }
      for labeled A:
      3.4 N*m{ 35 kgf*cm , 30 in.*lbf }
      for labeled B:
      5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



      B165501E02



    3. B165500
    4. Install 2 new clips.

      HINT:
      Use the same procedures for the RH side and LH side.



  1. w/ Fog Light:
    Install the front bumper bar.

    1. w/ Intuitive Parking Assist System:
      Connect the ultrasonic sensor connectors.



    2. Install the bumper bar with the 8 bolts and 3 screws.

      Torque:
      for bolt:
      32 N*m{ 326 kgf*cm , 24 ft.*lbf }
      for screw:
      3.4 N*m{ 35 kgf*cm , 30 in.*lbf }



      B165502E03



6. INSTALL REAR BUMPER COVER (for Resin Type Bumper)
  1. Attach the 4 claws to install the bumper cover.

  1. Install the 4 bolts and 2 nuts.

    Torque:
    for bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    for nut:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



  1. Install the 2 clips and 4 screws.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



    B166102



  1. w/ Intuitive Parking Assist System:
    Connect the connector and clamps shown in illustration.


    B166117



7. INSTALL REAR BUMPER PLATE RH

HINT:
Use the same procedures described for the LH side.



8. INSTALL REAR BUMPER PLATE LH


B166112
  1. Attach the 4 clips to install the bumper pad.



9. INSTALL REAR BUMPER PAD SUB-ASSEMBLY LH
  1. Attach the 14 clips to install the bumper pad.



  1. Install the clip.


    B166111



10. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



11. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH (for Resin Type Bumper)

HINT:
Use the same procedures described for the LH side.



12. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH


B166101
  1. Attach the claw to install the license plate light.

  1. Install the screw.



13. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH (for Resin Type Bumper)


B166101
  1. Attach the claw to install the license plate light.

  1. Install the screw.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).