Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front Side)

ULTRASONIC SENSOR (for Front Side) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH (for Steel Type Bumper)


B165877
  1. Remove the 3 clips, 2 screws and fender splash shield.



    B166707
  1. Remove the clip.

  1. Disconnect the fog light connector.



3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH (for Steel Type Bumper)

HINT:
Use the same procedures described for the LH side.



4. REMOVE FRONT END PANEL LH


B165496
  1. Using a clip remover, remove the 2 clips.

  1. Detach the 2 pins and remove the panel.



5. REMOVE FRONT END PANEL RH

HINT:
Use the same procedures described for the LH side.



6. REMOVE FRONT END PANEL LH (for Resin Type Bumper)


B165496
  1. Using a clip remover, remove the 2 clips.

  1. Detach the 2 pins and remove the panel.



7. REMOVE FRONT END PANEL RH (for Resin Type Bumper)

HINT:
Use the same procedures described for the LH side.



8. REMOVE FRONT BUMPER COVER SUB-ASSEMBLY
  1. Put protective tape around the bumper cover.

  1. Using a clip remover, remove the 8 clips.



  1. Remove the 16 bolts.


    B165498E01



    B165497
  1. Remove the screw and clip.

    HINT:
    Use the same procedures for the RH side and LH side.



  1. Detach the 4 claws and 2 pins and remove the bumper cover.


    B165499



9. REMOVE FRONT BUMPER BAR


    B165500
  1. w/o Fog Light:
    Remove the front bumper bar.

    1. Remove the 2 clips.

      HINT:
      Use the same procedures for the RH side and LH side.

    2. w/o Intuitive Parking Assist System:
      Remove the 8 bolts, 7 screws and front bumper bar.



    3. w/ Intuitive Parking Assist System:
      Remove the 8 bolts and 7 screws. Then disconnect the ultrasonic sensor connectors and remove the front bumper bar.


      B165501E01



  1. w/ Fog Light:
    Remove the front bumper bar.

    1. w/o Intuitive Parking Assist System:
      Remove the 8 bolts, 3 screws and bumper bar.



    2. w/ Intuitive Parking Assist System:
      Remove the 8 bolts and 3 screws. Then disconnect the ultrasonic sensor connectors and remove the front bumper bar.


      B165502E01



10. REMOVE FRONT BUMPER COVER (for Resin Type Bumper)


B165629E01
  1. Using a screwdriver, remove the 2 pin hold clips.

    HINT:
    Use the same procedures for the RH side and LH side.

  1. Using a clip remover, remove the 2 clips.

    HINT:
    Use the same procedures for the RH side and LH side.

  1. Put protective tape around the bumper cover.

  1. Using a clip remover, remove the 8 clips.



  1. Remove the 9 screws.


    B165630E01



  1. Detach the 4 claws and remove the bumper cover.


    B165636

  1. w/ Fog Light:
    Disconnect the fog light connectors and remove the bumper cover.

  1. w/ Intuitive Parking Assist System:
    Disconnect the ultrasonic sensor connectors and remove the bumper cover.



11. REMOVE NO. 1 ULTRASONIC SENSOR


    E134853
  1. While pushing down on the lever with a finger to release the one claw, detach the claw on the other side to remove the ultrasonic sensor.

    HINT:
    The type of claw on the top and bottom of the sensor are different. Observe the claws carefully before removing the sensor.



12. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER


    E146464
  1. Detach the 2 claws and remove the sensor retainer from the front bumper.