Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1340/47    Center Differential Lock Circuit

for Preparation Click here


DESCRIPTION

When the vehicle is changed to 4WD (L4L mode), VSC control turns off and the VSC OFF indicator light illuminates.

DTC Code
DTC Detection Condition
Trouble Area
C1340/47
When the terminal IG1 voltage is between 10 and 14 V, there is an open in the A.D.D. detection switch circuit or there is a transfer mechanical malfunction for 2 seconds or more.
  1. A.D.D. detection switch
  2. A.D.D. detection switch circuit
  3. 4WD control ECU
  4. Transfer
  5. Skid control ECU

WIRING DIAGRAM


C160162E01


INSPECTION PROCEDURE

NOTICE:
When replacing the VSC actuator assembly, perform zero point calibration (Click here).

HINT:
If the transfer shift actuator cannot change from 2WD to 4WD or 4WD to 2WD, inspect and repair the touch select 2-4 and high-low system first.

1.INSPECT SKID CONTROL ECU (EXI2 TERMINAL)


    C152724E05
  1. Disconnect the A17 ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A17-6 (EXI2) - Body ground
    1. Ignition switch ON
    2. 4WD (A.D.D. detection switch ON)
    Below 1.5 V
    A17-6 (EXI2) - Body ground
    1. Ignition switch ON
    2. 2WD (A.D.D. detection switch OFF)
    10 to 14 V



NG
Go to step 2
OK

REPLACE VSC ACTUATOR ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU)


    C152750E02
  1. Confirm that the skid control ECU connector and 4WD control ECU connector are properly connected.

  1. Disconnect the A17 and A25 ECU connectors.

  1. Disconnect the G1 A.D.D. actuator connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A17-6 (EXI2) - A25-15 (ADD)
    Always
    Below 1 Ω
    A17-6 (EXI2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BODY GROUND)


  1. Confirm that the 4WD control ECU connector and A.D.D. actuator connectors are properly connected.


    C159461E07

  1. Disconnect the A25 ECU connector.

  1. Inspect the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Connect the A25 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A25-15 (ADD) - Body ground
    4WD
    (A.D.D. detection switch ON)
    Below 1 Ω
    2WD
    (A.D.D. detection switch OFF)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE 4WD CONTROL ECU (Click here)