Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2240    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)

DTC    P2241    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)

DTC    P2242    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

DTC    P2255    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)

DTC    P2256    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

The A/F sensor, which is located between the exhaust manifold and catalyst, consists of alloyed metal elements and a heater.
Depending on the engine operating conditions, the heater heats the sensor elements to activate them. Battery voltage is applied to the heater, the sensor ground is controlled by the ECM using a duty ratio.
The sensor elements convert the oxygen concentration in the exhaust gas into voltage values to output. Based on the voltage, the ECM determines the air-fuel ratio and regulates the fuel injection volume depending on the air-fuel ratio and engine operating conditions. The voltage changes between 0.6 V and 4.5 V while the engine is running. If the air-fuel ratio is lean, which means the oxygen concentration in the exhaust gas is high, the voltage is high. If the air-fuel ratio is rich, which means the oxygen concentration in the exhaust gas is low, the voltage is low.

A160615E01


A178930E02


DTC Code
DTC Detection Condition
Trouble Area
P2237
P2240
Open in the circuit between terminals A1A+ and A1A-/A2A+ and A2A- of the AF sensor while engine is running
(2 trip detection logic)
  1. Open in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2238
P2241
Any of the following conditions are met
(2 trip detection logic)
  1. AF sensor output drops while engine is running.
  1. Voltage at terminal A1A+/A2A+ is 0.5 V or less.
  1. Voltage difference between terminals A1A+ and A1A-/A2A+ and A2A- is 0.1 V or less.
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2239
P2242
A1A+/A2A+ voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2252
P2255
A1A-/A2A- voltage 0.5 V or less
(2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2253
P2256
A1A-/A2A- voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the A/F sensor circuit, or if A/F sensor output drops. To detect these problems, the voltage of the A/F sensor is monitored when turning the ignition switch to the ON position, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in next driving cycle, the MIL will be illuminated and a DTC will be stored.

MONITOR STRATEGY


Related DTCs
P2237: A/F sensor (bank 1) open circuit between A1A+ and A1A-
P2238: A/F sensor (bank 1) short circuit between A1A+ and A1A-
P2238: A/F sensor (bank 1) short circuit between A1A+ and GND
P2238: A/F sensor (bank 1) low impedance
P2239: A/F sensor (bank 1) short circuit between A1A+ and +B
P2240: A/F sensor (bank 2) open circuit between A2A+ and A2A-
P2241: A/F sensor (bank 2) short circuit between A2A+ and A2A-
P2241: A/F sensor (bank 2) short circuit between A2A+ and GND
P2241: A/F sensor (bank 2) low impedance
P2242: A/F sensor (bank 2) short circuit between A2A+ and +B
P2252: A/F sensor (bank 1) short circuit between A1A- and GND
P2253: A/F sensor (bank 1) short circuit between A1A- and +B
P2255: A/F sensor (bank 2) short circuit between A2A- and GND
P2256: A/F sensor (bank 2) short circuit between A2A- and +B
Required Sensors/Components (Main)
A/F sensor
Required Sensors/Components (Related)
Engine Coolant Temperature (ECT) sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0016, P0018 (VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Meter)
P0110, P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0306 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2246, P2247 (Secondary Air Injection System)
P0500 (Vehicle Speed Sensor)
P0550 (IAC valve)

P2237 and P2240 (A/F sensor open circuit between A1A+ and A1A-/A2A+ and A2A-): 
Estimated sensor temperature
450 to 550°C (842 to 1022°F)
Engine
Running
Battery voltage
11 V or more

P2238 and P2241 (A/F sensor low impedance): 
Estimated sensor temperature
700 to 800°C (1292 to 1472°F)
Engine coolant temperature
5°C (41°F) or higher
Fuel cut
No executed

Other: 
Battery voltage
11 V or more
Ignition switch
ON
Time after ignition switch is OFF to ON
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P2237 and P2240 (A/F sensor open circuit between A1A+ and A1A-/A2A+ and A2A-): 
A/F sensor admittance
Below 0.002 1/Ω

P2238 and P2241 (A/F sensor low impedance): 
A/F sensor admittance
Below 0.022 1/Ω

P2238 and P2241 (A/F sensor short circuit between A1A+ and GND/A2A+ and GND): 
A1A+/A2A+ terminal voltage
0.5 V or less

P2239 and P2242 (A/F sensor short circuit between A1A+ and +B/A2A+ and +B): 
A1A+/A2A- terminal voltage
More than 4.5 V

P2252 and P2255 (A/F sensor short circuit between A1A- and GND/A2A- and GND): 
A1A-/A2A- terminal voltage
0.5 V or less

P2253 and P2256 (A/F sensor short circuit between A1A- and +B/A2A- and +B): 
A1A-/A2A- terminal voltage
More than 4.5 V

P2238 and P2241 (A/F sensor short circuit between A1A+ and A1A-/A2A+ and A2A-): 
Difference between A1A+ terminal and A1A- terminal voltage/A2A+ terminal and A2A- terminal voltage
0.1 V or less

COMPONENT OPERATING RANGE


A/F sensor admittance
0.022 1/Ω or more
A1A+/A2A+ terminal voltage
0.6 to 4.5 V
A1A-/A2A- terminal voltage
0.6 to 4.5 V
Difference between A1A+ and A1A- terminal voltages/A2A+ and A2A- terminal voltages
0.1 to 0.8 V

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the Techstream.
  1. Connect the Techstream to the DLC3.
  2. Start the engine and turn the Techstream ON.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the Techstream, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+25%
Rich
Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
More than 3.4 V
O2S B1 S2 or O2S B2 S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1 S2 or O2S B2 S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E05
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E05
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A160209E03
  1. Disconnect the D33*1 or D34*2 A/F sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D33-1 (HA1A) - D74-22 (HA1A)
    Always
    Below 1 Ω
    D34-1 (HA2A) - D74-20 (HA2A)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D33-1 (HA1A) or D74-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D34-1 (HA2A) or D74-20 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air-fuel ratio sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read pending DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2237, P2240, P2238, P2241, P2239, P2242, P2252, P2255, P2253 or P2256
    B



B
REPLACE ECM (Click here)
A

END