Home › ENGINE ยท 2UZ-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. Some systems need to be initialized after the cable is reconnected (Click here).
    2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



    A159706
  1. Disconnect the 2 fuel pump ECU connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the 2 fuel pump ECU connectors.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



3. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Remove the 2 nuts and throttle body cover.



4. REMOVE AIR CLEANER HOSE ASSEMBLY


    A153487
  1. Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.



5. DISCONNECT NO. 2 VENTILATION HOSE
  1. Disconnect the No. 2 ventilation hose from the ventilation valve.



6. DISCONNECT PURGE VSV


    A159752
  1. Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.

  1. Remove the bolt and disconnect the purge VSV from the intake manifold.



7. REMOVE THROTTLE BODY COVER BRACKET
  1. Remove the 2 bolts and 2 throttle body cover brackets.



8. DISCONNECT FUEL MAIN TUBE


    A160925
  1. Remove the fuel pipe clamp.

  1. Disconnect the fuel main tube (Click here).



9. DISCONNECT FUEL RETURN TUBE


    A160926
  1. Disconnect the fuel return tube (Click here).



10. DISCONNECT ENGINE WIRE


    A160928
  1. Disconnect the engine wire clamps from the No. 1 engine hanger and engine wire bracket.

  1. Disconnect the 2 wire clamps on the engine wire from the brackets on the RH delivery pipe.



11. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A160920
  1. Disconnect the fuel return hose from the pressure regulator.

    NOTICE:
    Put a cloth or equivalent under the pressure regulator.



    A160921
  1. Remove the 3 bolts and fuel return pipe from the delivery pipe and intake manifold.

    HINT:
    Move the fuel return pipe aside to secure more work space.



    A160927
  1. Remove the bolt, 2 union bolts, 4 gaskets and front fuel pipe.

  1. Disconnect the 8 injector connectors.

  1. Remove the 4 nuts holding the delivery pipes to the lower intake manifold.

  1. Remove the 2 delivery pipes.

    NOTICE:
    Be careful not to drop the injectors when removing the delivery pipes.



12. REMOVE FUEL INJECTOR ASSEMBLY


    A160930
  1. Remove the 8 injectors from the delivery pipe LH and RH.

    NOTICE:
    Do not apply any load to the injector in the horizontal direction.

  1. Remove the O-ring, grommet and insulator from each injector.