Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

DTC    B2343    Position Initialization Incomplete

for Preparation Click here


DESCRIPTION

This DTC is output when the sliding roof drive gear (sliding roof ECU) has not been initialized.

DTC Code
DTC Detection Condition
Trouble Area
B2343
Sliding roof drive gear (sliding roof ECU) has not been initialized
Sliding roof drive gear (sliding roof ECU)

WIRING DIAGRAM


B167040E02


INSPECTION PROCEDURE

1.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
  1. Check that the sliding roof drive gear can be initialized (Click here).

    OK:
    Sliding roof drive gear can be initialized.



NG
Go to step 3
OK


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC B2343 is output
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)
A

END 

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)


    B171201E01
  1. Disconnect the W3 ECU connector.

  1. Disconnect the W7 roof console box connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-1 (UP) - W7-6 (UP)
    Always
    Below 1 Ω
    W3-2 (DWN) - W7-5 (DWN)
    Always
    Below 1 Ω
    W3-6 (OPN) - W7-4 (OPN)
    Always
    Below 1 Ω
    W3-7 (CLS) - W7-3 (CLS)
    Always
    Below 1 Ω
    W7-6 (UP) - Body ground
    Always
    10 kΩ or higher
    W7-5 (DWN) - Body ground
    Always
    10 kΩ or higher
    W7-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    W7-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    W7-7 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT SLIDING ROOF SWITCH
B167041E02
  1. Remove the sliding roof switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UP) - 5 (E)
    TILT switch is pressed to up
    Below 1 Ω
    1 (UP) - 5 (E)
    TILT switch is not pressed to up
    10 kΩ or higher
    2 (DWN) - 5 (E)
    TILT switch is pressed to down
    Below 1 Ω
    2 (DWN) - 5 (E)
    TILT switch is not pressed to down
    10 kΩ or higher
    4 (OPN) - 5 (E)
    SLIDE switch is pressed to open
    Below 1 Ω
    4 (OPN) - 5 (E)
    SLIDE switch is not pressed to open
    10 kΩ or higher
    3 (CLS) - 5 (E)
    SLIDE switch is pressed to close
    Below 1 Ω
    3 (CLS) - 5 (E)
    SLIDE switch is not pressed to close
    10 kΩ or higher



NG
REPLACE SLIDING ROOF SWITCH (Click here)
OK


5.INSPECT ROOF CONSOLE BOX ASSEMBLY
E146741E05
  1. Remove the roof console box with sliding roof switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 7 (E)
    TILT switch is pressed to up
    Below 1 Ω
    6 (UP) - 7 (E)
    TILT switch is not pressed to up
    10 kΩ or higher
    5 (DWN) - 7 (E)
    TILT switch is pressed to down
    Below 1 Ω
    5 (DWN) - 7 (E)
    TILT switch is not pressed to down
    10 kΩ or higher
    4 (OPN) - 7 (E)
    SLIDE switch is pressed to open
    Below 1 Ω
    4 (OPN) - 7 (E)
    SLIDE switch is not pressed to open
    10 kΩ or higher
    3 (CLS) - 7 (E)
    SLIDE switch is pressed to close
    Below 1 Ω
    3 (CLS) - 7 (E)
    SLIDE switch is not pressed to close
    10 kΩ or higher



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)