Home › ENGINE · 1GR-FE › ENGINE MECHANICAL › VALVE CLEARANCE

VALVE CLEARANCE > ADJUSTMENT

for Preparation Click here



1. REMOVE INTAKE AIR SURGE TANK
  1. Remove the intake air surge tank (Click here).



2. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 6 ignition coil connectors.



    A151791
  1. Remove the 6 bolts and 6 ignition coils.



3. REMOVE SPARK PLUG
  1. Remove the 6 spark plugs.



4. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH


    A072943E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



5. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A072944E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



6. SET NO. 1 CYLINDER TO TDC / COMPRESSION


    A076530E01
  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.



    G038065E10
  1. Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.



7. INSPECT VALVE CLEARANCE


    G036072E05
  1. Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (Cold):
      Item
      Specified Condition
      Intake
      0.15 to 0.25 mm (0.00591 to 0.00984 in.)
      Exhaust
      0.29 to 0.39 mm (0.0114 to 0.0154 in.)

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.

  1. Turn the crankshaft 2/3 of a revolution (240°).



    G036073E04
  1. Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (Cold):
      Item
      Specified Condition
      Intake
      0.15 to 0.25 mm (0.00591 to 0.00984 in.)
      Exhaust
      0.29 to 0.39 mm (0.0114 to 0.0154 in.)

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.

  1. Turn the crankshaft 2/3 of a revolution (240°).



    A076345E06
  1. Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (Cold):
      Item
      Specified Condition
      Intake
      0.15 to 0.25 mm (0.00591 to 0.00984 in.)
      Exhaust
      0.29 to 0.39 mm (0.0114 to 0.0154 in.)

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.



8. ADJUST VALVE CLEARANCE


    A076530E01
  1. Set the No. 1 cylinder to TDC/compression.

    1. Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.



    2. G038065E10
    3. Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps shown in the illustration.
      If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.



    4. G038066E04
    5. Place paint marks on the chain links that correspond with the timing marks of the camshaft timing gears.



  1. Remove the No. 1 chain tensioner.

    NOTICE:
    1. Never rotate the crankshaft with the No. 1 chain tensioner removed.
    2. When rotating the camshaft with the No. 1 chain removed, turn the crankshaft counterclockwise 40° from the TDC first.




      A076506E01
    1. Remove the 4 bolts, timing chain cover plate and gasket.



    2. A072958E04
    3. While rotating the stopper plate of the No. 1 chain tensioner upward, push in the plunger of the No. 1 chain tensioner as shown in the illustration.

    4. While rotating the stopper plate of the tensioner downward, insert a bar of φ 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

    5. Remove the 2 bolts and No. 1 chain tensioner.



  1. Remove the No. 2 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.




      G038067E01
    1. While raising up the No. 2 chain tensioner, insert a pin of φ 1.0 mm (0.0394 in.) into the hole to fix it.



    2. G038068E01
    3. Hold the hexagonal portion of the No. 2 camshaft with a wrench, and remove the camshaft timing sprocket set bolt.

      NOTICE:
      Be careful not to damage the cylinder head and valve lifter with the wrench.

    4. Separate the camshaft timing gear from the No. 2 camshaft.



    5. G038069E01
    6. Rotate the camshaft counterclockwise using the wrench so that the cam lobes of the No. 1 cylinder face upward as shown in the illustration.



    7. A076510E13
    8. Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

    9. Remove the 4 bearing caps and No. 2 camshaft.



    G038070E01
  1. Remove the No. 2 chain tensioner.

    1. Remove the No. 2 chain tensioner bolt, No. 2 chain tensioner and camshaft timing sprocket.



  1. Remove the No. 1 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.




      G038072E01
    1. Hold the hexagonal portion of the No. 1 camshaft with a wrench, and loosen the camshaft timing gear set bolt.

      NOTICE:
      1. Be careful not to damage the cylinder head and valve lifter with the wrench.
      2. Do not disassemble the camshaft timing gear.



    2. G038071E01
    3. Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.



    4. G038073E01
    5. Rotate the No. 1 camshaft counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face downward as shown in the illustration.



    6. A076515E01
    7. Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

    8. Remove the 4 bearing caps.



    9. G038074E01
    10. Remove the camshaft timing gear set bolt with the No. 1 camshaft lifted up, and then remove the No. 1 camshaft and camshaft timing gear with No. 2 chain.



    11. A076517E01
    12. Tie the No. 1 chain with a string as shown in the illustration.

      NOTICE:
      Be careful not to drop anything inside the timing chain cover.



  1. Remove the No. 4 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.




      G038075E01
    1. While pushing down the No. 3 chain tensioner, insert a pin of φ 1.0 mm (0.0394 in.) into the hole to fix it.



    2. G038076E01
    3. Hold the hexagonal portion of the No. 4 camshaft with a wrench, and remove the camshaft timing sprocket set bolt.

      NOTICE:
      Be careful not to damage the cylinder head and valve lifter with the wrench.

    4. Separate the camshaft timing sprocket from the No. 4 camshaft.



    5. A076482E01
    6. Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

    7. Remove the 4 bearing caps and No. 4 camshaft.



    G038077E01
  1. Remove the No. 3 chain tensioner.

    1. Remove the No. 3 chain tensioner bolt, No. 3 chain tensioner and camshaft timing sprocket.



  1. Remove the No. 3 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.




      A076809E01
    1. Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

    2. Remove the 4 bearing caps.



    3. G038078E01
    4. Hold the No. 1 chain, and remove the No. 3 camshaft with camshaft timing gear and No. 2 chain.



    5. A076489E01
    6. Tie the No. 1 chain with a string as shown in the illustration.

      NOTICE:
      Be careful not to drop anything inside the timing chain cover.

  1. Remove the 24 valve lifters from the cylinder head LH and RH.



    A001082E01
  1. Determine the size of the valve lifter to be installed according to the following formulas or charts.

    1. Using a micrometer, measure the thickness of the removed lifter.

    2. Calculate the thickness of a new lifter so that the valve clearance comes within the specified value.

      T:
      Thickness of removed lifter

      A:
      Measured valve clearance

      N:
      Thickness of new lifter

      Intake:
      N = T + (A - 0.20 mm (0.00787 in.))

      Exhaust:
      N = T + (A - 0.30 mm (0.0118 in.))



    3. Select a new lifter with a thickness as close as possible to the calculated value.

      HINT:
      Lifters are available in 35 sizes in increments of 0.020 mm (0.000787 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).



      A158682E01

      Intake valve clearance (Cold):
      0.15 to 0.25 mm (0.00591 to 0.00984 in.)
      EXAMPLE:
      The 5.250 mm (0.2067 in.) shim is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) shim with a No. 46 lifter.


      New Lifter Thickness:

      Shim No.
      Thickness
      Shim No.
      Thickness
      Shim No.
      Thickness
      06
      5.060 mm (0.1992 in.)
      30
      5.300 mm (0.2087 in.)
      54
      5.540 mm (0.2181 in.)
      08
      5.080 mm (0.2000 in.)
      32
      5.320 mm (0.2094 in.)
      56
      5.560 mm (0.2189 in.)
      10
      5.100 mm (0.2008 in.)
      34
      5.340 mm (0.2102 in.)
      58
      5.580 mm (0.2197 in.)
      12
      5.120 mm (0.2016 in.)
      36
      5.360 mm (0.2110 in.)
      60
      5.600 mm (0.2205 in.)
      14
      5.140 mm (0.2024 in.)
      38
      5.380 mm (0.2118 in.)
      62
      5.620 mm (0.2213 in.)
      16
      5.160 mm (0.2031 in.)
      40
      5.400 mm (0.2126 in.)
      64
      5.640 mm (0.2220 in.)
      18
      5.180 mm (0.2039 in.)
      42
      5.420 mm (0.2134 in.)
      66
      5.660 mm (0.2228 in.)
      20
      5.200 mm (0.2047 in.)
      44
      5.440 mm (0.2142 in.)
      68
      5.680 mm (0.2236 in.)
      22
      5.220 mm (0.2055 in.)
      46
      5.460 mm (0.2150 in.)
      70
      5.700 mm (0.2244 in.)
      24
      5.240 mm (0.2063 in.)
      48
      5.480 mm (0.2157 in.)
      72
      5.720 mm (0.2252 in.)
      26
      5.260 mm (0.2071 in.)
      50
      5.500 mm (0.2165 in.)
      74
      5.740 mm (0.2260 in.)
      28
      5.280 mm (0.2079 in.)
      52
      5.520 mm (0.2173 in.)
      -
      -



      A158683E01

      Exhaust valve clearance (Cold):
      0.29 to 0.39 mm (0.0114 to 0.0154 in.)
      EXAMPLE:
      The 5.340 mm (0.210 in.) shim is installed, and the measured clearance is 0.480 mm (0.0189 in.). Replace the 5.340 mm (0.210 in.) shim with a No. 48 lifter.


      New Lifter Thickness:

      Shim No.
      Thickness
      Shim No.
      Thickness
      Shim No.
      Thickness
      06
      5.060 mm (0.1992 in.)
      30
      5.300 mm (0.2087 in.)
      54
      5.540 mm (0.2181 in.)
      08
      5.080 mm (0.2000 in.)
      32
      5.320 mm (0.2094 in.)
      56
      5.560 mm (0.2189 in.)
      10
      5.100 mm (0.2008 in.)
      34
      5.340 mm (0.2102 in.)
      58
      5.580 mm (0.2197 in.)
      12
      5.120 mm (0.2016 in.)
      36
      5.360 mm (0.2110 in.)
      60
      5.600 mm (0.2205 in.)
      14
      5.140 mm (0.2024 in.)
      38
      5.380 mm (0.2118 in.)
      62
      5.620 mm (0.2213 in.)
      16
      5.160 mm (0.2031 in.)
      40
      5.400 mm (0.2126 in.)
      64
      5.640 mm (0.2220 in.)
      18
      5.180 mm (0.2039 in.)
      42
      5.420 mm (0.2134 in.)
      66
      5.660 mm (0.2228 in.)
      20
      5.200 mm (0.2047 in.)
      44
      5.440 mm (0.2142 in.)
      68
      5.680 mm (0.2236 in.)
      22
      5.220 mm (0.2051 in.)
      46
      5.460 mm (0.2150 in.)
      70
      5.700 mm (0.2244 in.)
      24
      5.240 mm (0.2063 in.)
      48
      5.480 mm (0.2157 in.)
      72
      5.720 mm (0.2252 in.)
      26
      5.260 mm (0.2071 in.)
      50
      5.500 mm (0.2165 in.)
      74
      5.740 mm (0.2260 in.)
      28
      5.280 mm (0.2079 in.)
      52
      5.520 mm (0.2173 in.)
      -
      -



  1. Install the No. 3 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.




      A076490E05
    1. Align the mark link (yellow) with the timing mark (2-dot mark) of the camshaft timing gear shown in the illustration.

    2. Apply a light coat of engine oil to the thrust portions and journals of the No. 3 camshaft.



    3. G038079E01
    4. Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.



    5. G038080E01
    6. Set the No. 3 camshaft onto the cylinder head LH with the cam lobes of the No. 2 cylinder facing downward as shown in the illustration.

    7. Apply a light coat of engine oil to the 4 bearing caps.



    8. A076494E01
    9. Install the 4 bearing caps in their proper locations.

    10. Apply a light coat of engine oil to the threads of the 8 bearing cap bolts.



    11. A076487E06
    12. Uniformly install the 8 bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      for 10 mm head:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
      for 12 mm head:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }



    13. G038081E03
    14. Set the paint mark of the No. 1 chain between the timing marks of the camshaft timing gear.



    A076289E01
  1. Install the No. 3 chain tensioner.

    1. While pushing in the tensioner, insert a pin of φ 1.0 mm (0.0394 in.) into the hole to fix it.



    2. G038082E04
    3. Temporarily install the camshaft timing sprocket and No. 3 chain tensioner, and align the mark links (yellow) with the timing marks (1-dot mark and 2-dot mark) of the camshaft timing gear and sprocket.

    4. Apply a light coat of engine oil to the threads and under the head of the No. 3 chain tensioner bolt.

    5. Install the No. 3 chain tensioner with the bolt.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }



  1. Install the No. 4 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. Apply a light coat of engine oil to the thrust portions and journals of the No. 4 camshaft.

    2. Apply a light coat of engine oil to the threads and under the head of the camshaft timing gear set bolt.



    3. G038083E01
    4. Align the knock pin hole on the camshaft timing sprocket with the knock pin of the No. 4 camshaft, and insert the No. 4 camshaft into the camshaft timing sprocket.

    5. Temporarily install the camshaft timing gear set bolt.



    6. A134498
    7. Install the 4 bearing caps in their proper locations.

    8. Apply a light coat of engine oil to the threads and under the heads of the 8 bearing cap bolts.



    9. A076482E07
    10. Uniformly install the 8 bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      for 10 mm head:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
      for 12 mm head:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }



    11. G038076E01
    12. Hold the hexagonal portion of the No. 4 camshaft with a wrench, and tighten the camshaft timing gear set bolt.

      Torque:
      100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    13. Remove the pin from the No. 3 chain tensioner.



  1. Install the No. 1 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.




      A076518E05
    1. Align the mark link (yellow) with the timing mark (1-dot mark) of the camshaft timing gear as shown in the illustration.

    2. Apply a light of engine oil to the thrust portions and journals of the camshafts.



    3. A076519E01
    4. Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.



    5. G038084E01
    6. Align the knock pin hole of the camshaft timing gear with the knock pin of the No. 1 camshaft, and insert the No. 1 camshaft into the camshaft timing gear.

    7. Apply a light coat of engine oil to the threads and under the head of the camshaft timing gear set bolt.

    8. Temporarily install the camshaft timing gear set bolt.



    9. G038085E02
    10. Set the No. 1 camshaft onto the cylinder head RH with the cam lobes of the No. 1 cylinder facing downward as shown in the illustration.

    11. Apply a light coat of engine oil to the 4 bearing caps.



    12. A076522E01
    13. Install the 4 bearing caps in their proper locations.

    14. Apply a light coat of engine oil to the threads and under the heads of the 8 bearing cap bolts.



    15. A076515E08
    16. Uniformly install the 8 bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      for 10 mm head:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
      for 12 mm head:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }



    17. G038086E03
    18. Rotate the No. 1 camshaft clockwise using the hexagonal portion of the No. 1 camshaft so that the timing mark of the camshaft timing gear is aligned with the timing mark of the camshaft bearing cap.



    19. G038087E03
    20. Align the paint mark of the No. 1 chain with the timing mark of the camshaft timing gear.



    21. G038072E01
    22. Hold the hexagonal portion of the No. 1 camshaft with a wrench, and tighten the camshaft timing gear set bolt.

      Torque:
      100 N*m{ 1020 kgf*cm , 74 ft.*lbf }



    A076286E01
  1. Install the No. 2 chain tensioner.

    1. While pushing in the tensioner, insert a pin of φ 1.0 mm (0.0394 in.) into the hole to fix it.



    2. G038088E03
    3. Temporarily install the camshaft timing sprocket and No. 2 chain tensioner and align the mark links (yellow) with the timing marks (1-dot mark) of the camshaft timing gear and sprocket.

    4. Apply a light coat of engine oil to the threads and under the head of the No. 2 chain tensioner bolt.

    5. Install the No. 2 chain tensioner with the bolt.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }



  1. Install the No. 2 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. Apply a light coat of engine oil to the thrust portions and journals of the No. 2 camshaft.



    2. G038089E01
    3. Set the No. 2 camshaft onto the cylinder head RH with the cam lobes of the No. 1 cylinder facing upward as shown in the illustration.

    4. Apply a light coat of engine oil to the 4 bearing caps.



    5. A134509
    6. Install the 4 bearing caps in their proper locations.

    7. Apply a light coat of engine oil to the threads and under the heads of the 8 bearing cap bolts.



    8. A076510E14
    9. Uniformly install the 8 bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      for 10 mm head:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
      for 12 mm head:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }



    10. G038090E03
    11. Rotate the No. 2 camshaft clockwise using a wrench so that the knock pin of the No. 2 camshaft is aligned with the knock pin hole of the camshaft timing sprocket.

    12. Apply a light coat of engine oil to the threads and under the head of the camshaft timing sprocket set bolt.



    13. G038068E01
    14. Hold the hexagonal portion of the No. 2 camshaft with a wrench, and install the camshaft timing sprocket set bolt.

      Torque:
      100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    15. Remove the pin from the No. 2 chain tensioner.



    A076294E06
  1. Install the No. 1 chain tensioner.

    1. While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.

    2. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ 3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate.

    3. Apply a light coat of engine oil to the threads and under the heads of the 2 No. 1 chain tensioner bolts.

    4. Install the No. 1 chain tensioner with the 2 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    5. Remove the bar from the chain tensioner.



    6. A076506E01
    7. Install a new gasket and the timing chain cover plate with the 4 bolts.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    8. A076530E01
    9. Turn the crankshaft pulley 2 complete revolutions slowly, and align the notch with the timing mark "0" of the timing chain cover.



    10. G038065E10
    11. Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps shown in the illustration.



9. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.



    A076311E06
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.



    A072944E02
  1. Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



10. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.



    A076310E07
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.



    A072943E02
  1. Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



11. INSTALL SPARK PLUG
  1. Using a 16 mm plug wrench, install the 6 spark plugs.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



12. INSTALL IGNITION COIL ASSEMBLY


    A151791
  1. Install the 6 ignition coils with the 6 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 6 ignition coil connectors.



13. INSTALL INTAKE AIR SURGE TANK
  1. Install the intake air surge tank (Click here).



14. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems OFF.
  1. Perform the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter the following menus:
      Select: Powertrain / Engine and ECT / Data List / All Data / IGN Advance

    3. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idling (transmission in neutral position and A/C switch OFF)

    4. Check that the ignition timing advances immediately when the engine speed is increased.



    H102392E79
  1. When not using Techstream:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be sure not to improperly connect the terminals. This may damage the engine.

    2. Remove the air cleaner cap.



    3. A158636
    4. Pull out the wire harness as shown in the illustration.

    5. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects primary signals.
      1. After checking, be sure to wrap the wire harness with tape.



    6. A076316E01
    7. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idling (transmission in neutral position and A/C switch OFF)

    8. Remove SST from the DLC3.

    9. Inspect the ignition timing during idling.

      Standard ignition timing:
      7 to 24° BTDC @ idling (transmission in neutral position and A/C switch OFF)

    10. Disconnect the timing light from the engine.

    11. Install the air cleaner cap.