Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. Some systems need to be initialized after the cable is reconnected (Click here).
    2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



    A159706
  1. Disconnect the 2 fuel pump ECU connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the 2 fuel pump ECU connectors.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A151786E01

  1. Tighten the radiator drain cock plug by hand.



4. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. DISCONNECT HOOD SUPPORT ASSEMBLY


    B167795
  1. Using a screwdriver, remove the hood support assembly while releasing the 2 clips.

    HINT:
    Tape the screwdriver tip before use.

    CAUTION:
    Remove the hood support while supporting the hood by hand.



7. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the 4 bolts and hood.



8. REMOVE FRONT WIPER MOTOR AND LINK
  1. Remove the front wiper motor and link (Click here).



9. REMOVE FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the 2 washer hoses.



  1. Remove the 7 bolts and front cowl top outer panel.


    A151796



10. REMOVE V-BANK COVER


    A112983E03
  1. Remove the 2 nuts and V-bank cover.



11. REMOVE NO. 2 AIR CLEANER HOSE


A151771
  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner hose.



12. REMOVE AIR CLEANER ASSEMBLY WITH ELEMENT


    A151812
  1. Disconnect the No. 2 ventilation hose.

  1. Detach the hose clamp.



    A151769
  1. Disconnect the vacuum hose.

  1. Disconnect the MAF meter connector.

  1. Using a clip remover, detach the 2 wire harness clamps.



    A151770
  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner with element.



13. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 5 bolts, 3 screws and engine under cover.



14. REMOVE INTAKE AIR SURGE TANK


    A151856
  1. Disconnect the throttle position sensor and throttle control motor connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.



    A151765
  1. Disconnect the purge line hose.

  1. Disconnect the purge VSV connector.

  1. Disconnect the union to check valve hose.



    A151766
  1. Disconnect the No. 1 ventilation hose.



    A151768
  1. Disconnect the vacuum switching valve (for ACIS) connector.

  1. Using a clip remover, detach the 2 wire harness clamps.



    A151767
  1. Remove the 2 bolts and throttle body bracket.



    A151773
  1. Using a clip remover, detach the wire harness clamp.

  1. Remove the bolt and oil baffle plate.



    A151772
  1. Remove the 2 bolts and No. 1 surge tank stay.

  1. Remove the 2 bolts and No. 2 surge tank stay.



    A075648E05
  1. Remove the 2 nuts.

  1. Using an 8 mm hexagon wrench, remove the 4 bolts. Then remove the intake air surge tank and gasket.



15. DISCONNECT ENGINE WIRE


    A158551E01
  1. Engine Room RH Side:

    1. Disconnect the ECM connector labeled A as shown in the illustration.

    2. Remove the junction block cover.

    3. Disconnect the 7 connectors from junction block labeled B shown in the illustration.

    4. Using a clip remover, detach the 2 wire harness clamps labeled B shown in the illustration.

    5. Remove the 2 bolts and ground cable labeled C shown in the illustration.

    6. Disconnect the 2 air pump connectors labeled D shown in the illustration.

    7. Using a clip remover, detach the 2 wire harness clamps labeled E shown in the illustration.

    8. Remove the bolt and bracket labeled F shown in the illustration.



    A158552E01
  1. Engine Room LH Side:

    1. Disconnect the 4 connectors from the air injection control driver labeled A shown in the illustration.

    2. Remove the engine room relay block cover.

    3. Disconnect the 2 connectors from the engine room junction block labeled B shown in the illustration.

    4. Remove the nut from the engine room junction block, and disconnect the No. 2 engine wire's cover labeled C shown in the illustration.

    5. Remove the nut and disconnect the wire harness bracket from the inner body panel side labeled D shown in the illustration.

    6. Disconnect the connector, and using a clip remover, detach the front ABS junction connector's clamp from the engine room relay block side labeled E shown in the illustration.

    7. Disconnect the connector from the crankshaft position sensor labeled F shown in the illustration.

    8. Using a clip remover, detach the wire harness clamp from the front engine mounting bracket LH labeled F shown in the illustration.

    9. Remove the bolt and ground cable labeled G shown in the illustration.

    10. Pull out the battery positive cable cover, and then remove the nut and battery positive cable labeled H shown in the illustration.



16. REMOVE NO. 5 AIR INJECTION SYSTEM HOSE


    A147039
  1. Disconnect the 2 air pump connectors.



    A147040
  1. Detach the wire harness clamp and remove the bolt, then disconnect the wire harness bracket.



    A153426E01
  1. Remove the air injection system hose.



17. REMOVE NO. 4 AIR INJECTION SYSTEM HOSE


18. REMOVE NO. 1 AIR TUBE
  1. Remove the 2 bolts, 2 nuts, No. 1 air tube and 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



19. DISCONNECT NO. 2 AIR TUBE
  1. Disconnect the wire harness clamp.

  1. Remove the bolts and 4 nuts, then disconnect the No. 2 air tube.



  1. Remove the 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



    A153458E01



20. REMOVE AIR SWITCHING VALVE ASSEMBLY


    A153459
  1. Remove the 2 nuts, bolt and air switching valve.



21. REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY (for Regular Cab Standard Deck)
  1. Remove the 2 bolts.

  1. Disconnect the front No. 3 exhaust pipe from the exhaust pipe support.



22. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for Regular Cab Standard Deck)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Remove the 3 nuts and front No. 2 exhaust pipe.



23. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (except Regular Cab Standard Deck)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Remove the 3 nuts.

  1. Disconnect the front No. 2 exhaust pipe from the exhaust pipe support.



24. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Detach the 2 heated oxygen sensor wire clamps.

  1. Remove the 3 nuts and front exhaust pipe.



25. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A151777E01
  1. Remove the 6 nuts, exhaust manifold and gasket.



26. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A151779E01
  1. Remove the 3 bolts and heat insulator.



27. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
  1. Remove the 6 nuts, exhaust manifold and gasket.



28. DISCONNECT RADIATOR HOSE INLET


29. DISCONNECT RADIATOR HOSE OUTLET


30. REMOVE FAN SHROUD


    A134581
  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).



    A151755
  1. Disconnect the reservoir hose from the radiator tank upper.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



31. REMOVE RADIATOR SIDE DEFLECTOR RH


    A151775
  1. Using a clip remover, remove the 6 clips and side deflector.



32. REMOVE RADIATOR SIDE DEFLECTOR LH


    A151774
  1. Remove the wire harness clamp.

  1. Using a clip remover, remove the 6 clips and side deflector.



33. REMOVE RADIATOR ASSEMBLY


    A151751
  1. Remove the 4 bolts and radiator.



34. DISCONNECT HEATER WATER HOSE


A151225
  1. Remove the wire harness clamp.

  1. Disconnect the heater water inlet and outlet hose.

  1. Remove the nut and heater water pipe bracket.



35. DISCONNECT VANE PUMP ASSEMBLY


    A076444E03
  1. Disconnect the power steering oil pressure switch connector.

  1. Remove the 2 bolts, and disconnect the vane pump.

    NOTICE:
    Do not hit other parts with the pulley when separating the vane pump.

    HINT:
    Make sure to suspend the vane pump securely.



36. REMOVE GENERATOR ASSEMBLY


    A152255
  1. Remove the nut and disconnect the wire harness clamp bracket.



    A152256
  1. Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the wire harness clamp.

  1. Remove the bolt and disconnect the wire harness clamp bracket.



    A152257
  1. Remove the 2 bolts and generator.



37. DISCONNECT COOLER COMPRESSOR


    A158632
  1. Remove the 2 nuts, 2 bolts and disconnect the cooler compressor.



38. DISCONNECT NO. 1 AND NO. 2 FUEL PIPE


A151228


  1. Disconnect the No. 1 and No. 2 fuel pipe.



      C157056E04
    1. Remove the fuel pipe clamp from the fuel tube connector.

      HINT:
      Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.



    2. A088336E04
    3. Pinch the connector and disconnect the connector and pipe.

      HINT:
      If the connector and the pipe are stuck together, pinch the connector, push and pull the pipe to disconnect the pipe and pull it out.

      NOTICE:
      Do not use any tools.

    4. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.



    5. A099427E05
    6. To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.



39. REMOVE BATTERY


40. REMOVE FRONT FENDER APRON SEAL LH


41. REMOVE FRONT FENDER APRON SEAL RH


42. REMOVE STARTER ASSEMBLY
  1. Remove the starter (for 1.6 kW Type) .

  1. Remove the starter (for 2.0 kW Type) .



43. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    C157016
  1. Remove the flywheel housing side cover.



    C157017
  1. Turn the crankshaft to gain access to the 6 bolts and remove the 6 bolts while holding the crankshaft pulley set bolt with a wrench.



44. REMOVE FLYWHEEL HOUSING UNDER COVER


    A076446E03
  1. Remove the flywheel housing under cover.



45. REMOVE PROPELLER SHAFT ASSEMBLY (for 2 Joint Type)


C158582E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 bolts and 4 nuts. Then disconnect the propeller shaft from the differential side.

  1. Remove the propeller shaft.



    C164127E01
  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



    C160071E01
  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-60010  



46. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 3 Joint Type)


C158582E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 bolts and 4 nuts. Then disconnect the propeller shaft from the differential side.



  1. w/o Bearing Washer:



      C158583
    1. Remove the 2 mounting bolts from the crossmember.

  1. w/ Bearing Washer:

    1. Remove the 2 mounting bolts and 2 bearing washers from the crossmember.

  1. Remove out the propeller shaft.



    C164127E01
  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



    C160071E01
  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-60010  



47. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C155905
  1. Remove the nut and clip, and disconnect the transmission control cable.



48. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C112848
  1. Support the transmission with a transmission jack.
    Lift the transmission slightly from the crossmember.



49. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    C155908
  1. Remove the 4 bolts of the rear No. 1 engine mounting insulator.



    C155907
  1. Remove the 4 nuts, 4 washers, 4 bolts and No. 3 frame crossmember.



50. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


    C155909
  1. Remove the 4 bolts and engine mounting insulator.



51. DISCONNECT WIRE HARNESS AND CONNECTOR


C155915
  1. Remove the bolt and disconnect the ground cable.



    C112849
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



    C155912E01
  1. Disconnect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.

    HINT:
    Detach the claw, press down the lever, and then disconnect the transmission wire connector.

  1. Disconnect the 4 connector clamps and 4 harness clamps.

  1. Remove the bolt and disconnect the harness clamp and wire harness.



52. DISCONNECT NO. 1 WATER BY-PASS PIPE


    C158364
  1. Remove the 2 bolts and disconnect the 2 water by-pass hoses from the transmission oil cooler, and separate the by-pass pipe from the automatic transmission.

    NOTICE:
    Use a container to catch any coolant which flows out of the water by-pass hoses.



53. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


C157018
  1. Remove the 9 bolts and transmission.

    NOTICE:
    Do not use excess force when prying the transmission assembly.



54. REMOVE ENGINE ASSEMBLY


    A072941E02
  1. Install the 2 engine hangers with the 4 bolts shown in the illustration.
    Part No.: 
    Item
    Part No.
    No. 1 engine hanger
    12281-31060
    No. 2 engine hanger
    12282-31040
    Bolt
    90119-08A87

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



    A158524
  1. Attach the engine sling device and hang the engine with the chain block.



    A151278
  1. Remove the 2 nuts and 4 bolts from the front engine mounting insulator LH and RH.

  1. Lift the engine out of the vehicle carefully.

    NOTICE:
    Make sure the engine is clear of all wiring and hoses.

  1. Remove the front engine mounting insulator LH and RH.

  1. Place the engine onto a working bench.



55. REMOVE DRIVE PLATE AND RING GEAR


    A076326E05
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A151280
  1. Remove the 8 bolts, rear spacer, drive plate and front spacer.



56. INSTALL ENGINE STAND
  1. Install the engine onto an engine stand with the bolts.



57. REMOVE ENGINE HANGER


    A072941E02
  1. Remove the 4 bolts and 2 engine hangers.