RADIATOR > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
![]() |
Set the radiator bracket hooks to the radiator support holes.
Install the radiator with the 4 bolts.
| 2. INSTALL RADIATOR HOSE OUTLET |
| 3. INSTALL FAN SHROUD |
Install the fan pulley to the water pump.
Place the shroud together with the coupling fan between the radiator and engine.
Install the fluid coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud's claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the radiator tank upper.
Install the fan and generator V-belt.
![]() |
Tighten the 4 nuts of the fluid coupling fan.
| 4. INSTALL RADIATOR HOSE INLET |
| 5. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose.
Connect the vacuum hose and No. 2 ventilation hose.
| 6. INSTALL OIL COOLER ASSEMBLY (w/ Trailer Towing System) |
![]() |
Install the No. 1 and No. 2 oil cooler air ducts with the 4 bolts.
Install the and oil cooler support with the 2 bolts.
![]() |
Temporarily place the oil cooler on the radiator support.
Install the 3 bolts.
Install the oil cooler with the 3 bolts.
| 7. CONNECT NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE (w/ Trailer Towing System) |
![]() |
Connect the 2 hoses.
Attach the claw to close the flexible hose clamp.
| 8. INSTALL RADIATOR SIDE DEFLECTOR RH (w/o Trailer Towing System) |
![]() |
Install the deflector with the 6 clips.
| 9. INSTALL RADIATOR SIDE DEFLECTOR LH |
![]() |
Install the deflector with the 6 clips.
Install the wire harness clamp.
| 10. INSTALL FRONT BUMPER COVER (w/ Trailer Towing System) |
For resin type, refer to the following procedures (Click here).
Except resin type, refer to the following procedures. (Click here).
| 11. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines. If the coolant level is below the LOW line, repeat all of the procedures above. If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 12. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 13. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY |
![]() |
Install the 2 throttle body cover brackets with the 2 bolts.
![]() |
Install the throttle body cover with the 2 cap nuts.
| 14. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover onto the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.