Home › ENGINE ยท 2UZ-FE › ENGINE MECHANICAL › TIMING BELT

TIMING BELT > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and setting. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.
  2. Some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



    A156211E01

  1. Tighten the radiator drain cock plug by hand.



4. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Remove the 2 nuts and throttle body cover.



5. REMOVE AIR CLEANER HOSE ASSEMBLY


    A153487
  1. Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.



6. REMOVE AIR CLEANER ASSEMBLY


    A156196E01
  1. Remove the air cleaner cap.

    1. Disconnect the MAF meter connector.

    2. Using a clip remover, detach the wire harness clamp.

    3. Unfasten the 4 hook clamps and then remove the air cleaner cap.

  1. Remove the air cleaner element.



    A156197
  1. Remove the 2 bolts and air cleaner case.



7. REMOVE RADIATOR HOSE INLET


8. REMOVE RADIATOR HOSE OUTLET


9. REMOVE FAN AND GENERATOR V BELT


    B000809E02
  1. Loosen the belt tension by turning the belt tensioner counterclockwise, and then remove the fan and generator V belt.

    HINT:
    The pulley bolt for the belt tensioner has left-hand thread.



10. REMOVE FLUID COUPLING ASSEMBLY


    A123358
  1. Loosen the 4 fluid coupling nuts.



    A151755E01
  1. Remove the 2 bolts and fluid coupling nuts. Then remove the fan together with the fan shroud.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley.



11. DISCONNECT COOLER COMPRESSOR ASSEMBLY


    A160758
  1. Disconnect the connector.

  1. Remove the 3 bolts, nut and No. 1 compressor stay and disconnect the cooler compressor.



12. DISCONNECT VANE PUMP ASSEMBLY
  1. Disconnect the connector.

  1. Remove the nut, 2 bolts and vane pump assembly.

    HINT:
    Hang up the hoses instead of detaching them.



13. REMOVE GENERATOR ASSEMBLY


    A152261
  1. Disconnect the generator connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.

  1. Remove the bolt and disconnect the wire harness bracket from the generator.



    A152262
  1. Remove the bolt, 2 nuts and generator.



14. REMOVE OIL COOLER PIPE


    A108784E04
  1. Remove the cap nut and bolt.

  1. Using needle-nose pliers, grip the claws of the clamps and slide the clamps to disconnect the 3 water by-pass hoses and remove the oil cooler pipe.



15. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A110456
  1. Remove the pulley bolt, cover plate and idler pulley.



16. REMOVE NO. 3 TIMING BELT COVER SUB-ASSEMBLY RH


    A123359
  1. Remove the 3 bolts, nut and timing belt cover.



17. REMOVE NO. 3 TIMING BELT COVER SUB-ASSEMBLY LH


    A014424E08
  1. Disconnect the engine wire from the 2 wire clamps.

  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the camshaft position sensor wire from the wire clamp on the timing belt cover.

  1. Remove the wire grommet from the timing belt cover.

  1. Remove the 4 bolts.

  1. Pull the cover outward, pull the camshaft position sensor wire out of the cover, and remove the cover.



18. REMOVE NO. 2 TIMING BELT COVER SUB-ASSEMBLY


    A110458
  1. Remove the 2 bolts and timing belt cover.



19. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A160748
  1. Remove the bolt, 2 nuts and V-ribbed belt tensioner.



20. REMOVE FAN BRACKET SUB-ASSEMBLY


    A115076
  1. Remove the 2 nuts, 2 bolts and fan bracket.



21. REMOVE CRANKSHAFT PULLEY


    A123364E02
  1. Using SST, remove the pulley set bolt.

    SST
    09213-70011  
    09330-00021  



    A160749E01
  1. Using SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09953-05020, 09954-05021)



22. REMOVE NO. 1 TIMING BELT COVER


    A072694E02
  1. Remove the 4 bolts, timing belt cover, cover spacer and gasket.



23. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE


A072696E01


24. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily install the pulley set bolt.



    A160757E01
  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



25. REMOVE TIMING BELT


  1. Set the No. 1 cylinder to approximately 45° BTDC/compression.



      A160750E01
    1. Using the pulley set bolt, turn the crankshaft counterclockwise by approximately 45°.

      NOTICE:
      If the timing belt is disengaged, having the crankshaft pulley at a wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft timing pulley and camshaft, causing damage. So always set the crankshaft pulley at the correct angle.



    A072697E01
  1. Alternately loosen the 2 bolts, then remove the bolts, timing belt tensioner and dust boot.



    A160800
  1. Using a wrench, loosen the tension between the camshaft timing pulley (for bank 2) and crankshaft timing pulley by turning the camshaft timing pulley (for bank 2) counterclockwise slightly.

  1. Disconnect the timing belt from the No. 1 timing belt idler and remove the timing belt.



26. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


    A072698E01
  1. Using a 10 mm hexagon wrench, remove the bolt, idler and plate washer.



27. REMOVE NO. 2 TIMING BELT IDLER SUB-ASSEMBLY


    A072699E01
  1. Remove the bolt and idler.