Home › ENGINE ยท 1GR-FE › LUBRICATION › OIL PUMP

OIL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL FRONT CRANKSHAFT OIL SEAL


    A134551E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09226-10010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap oil seal at an angle.

  1. Apply MP grease to the lip of the oil seal.



2. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.



    A134563E01
  1. Install a new O-ring to the cylinder head for bank 2 side.



    A134564E02
  1. Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    Standard seal diameter:
    3 to 4 mm (0.118 to 0.157 in.)

    NOTICE:
    Remove any oil from the contact surface.



  1. Apply seal packing in a continuous line to the timing chain cover as shown in the illustration below.

    Seal packing:
    for oil related part:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    for water related part:
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    HINT:
    Water related part is labeled "B" shown in the illustration below.

    Standard seal diameter:
    3.5 to 4.0 mm (0.138 to 0.157 in.)

    NOTICE:
    1. When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.
    4. Do not apply seal packing to "A" shown in the illustration below.



    A158650E01



    A134566E01
  1. Align the key way of the oil pump drive rotor with the rectangular portion of the crankshaft timing gear, and slide the timing chain cover into place.



    A158566E01
  1. Install the timing chain cover with the 24 bolts (A and B) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    Standard bolt length 
    Item
    Quantity
    Length
    Bolt A
    9
    25 mm (0.984 in.)
    Bolt B
    15
    55 mm (2.17 in.)



3. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.



    A076306E03
  1. Install a new O-ring to the oil pan.



    A134571E03
  1. Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3 to 4 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.



    A151272E02
  1. Install the oil pan with the 17 bolts (A, B and C) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A, B and nut:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt C:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Standard bolt length 
    Item
    Quantity
    Length
    A
    6
    25 mm (0.984 in.)
    B
    9
    45 mm (1.77 in.)
    C
    2
    14 mm (0.551 in.)



4. INSTALL OIL STRAINER SUB-ASSEMBLY


    A151271
  1. Install a new gasket and the oil strainer with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



5. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY


    A151274E02
  1. Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3 to 4 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan No. 2 within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.



    A151269E01
  1. Install the No. 2 oil pan with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt:
    9.0 N*m{ 92 kgf*cm , 81 in.*lbf }
    for nut:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL ENGINE OIL DIPSTICK GUIDE


    A158543E01
  1. Install a new O-ring to the dipstick guide.

  1. Apply a light coat of engine oil to the O-ring.

  1. Push the dipstick guide end into the guide hole.

  1. Install the dipstick guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



7. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.



    A076310E07
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.



    A072943E02
  1. Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



8. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.



    A076311E06
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.



    A072944E02
  1. Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



9. INSTALL VVT SENSOR


    G038105
  1. Apply a light coat of engine oil to the O-ring of the sensor.

  1. Install the sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the sensor connector.



10. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A093611E01
  1. Apply a light coat of engine oil to a new O-ring of the camshaft timing oil control valve and install the O-ring.



    A158547E02
  1. Install the camshaft timing oil control valve with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful that the O-ring is not cracked when installing the camshaft timing oil control valve.



11. INSTALL SPARK PLUG
  1. Using a 16 mm plug wrench, install the 6 spark plugs.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



12. INSTALL IGNITION COIL ASSEMBLY


    A151791
  1. Install the 6 ignition coils with the 6 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 6 ignition coil connectors.



13. INSTALL WATER INLET HOUSING


    A134567E01
  1. Apply soapy water to a new O-ring, install it to the water outlet pipe.

  1. Install a new O-ring to the water pump.

  1. Install a new gasket to the water pump.



    A134568
  1. Install the water inlet with the 5 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



14. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY
  1. Set a new O-ring to the timing chain cover.



    A151244
  1. Install the oil filter bracket with the 3 bolts and 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



15. CONNECT OIL COOLER HOSE


A151242E02


16. CONNECT NO. 2 OIL COOLER HOSE


17. INSTALL CRANKSHAFT PULLEY


    A076309E03
  1. Using SST, install the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    250 N*m{ 2549 kgf*cm , 184 ft.*lbf }



18. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A076438E01
  1. Install the No. 1 idler pulley with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    HINT:
    "DOUBLE" is marked on the No. 1 idler pulley to distinguish it from the No. 2 idler pulley.



19. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

NOTICE:
The installation of the No. 2 idler pulleys differs depending on the mark on the No. 2 idler pulleys shown in the illustration.

A191316E01

HINT:
Use the same procedure for both No. 2 idler pulleys.



  1. w/ Idler Pulley Cover Plate (PU107013ARMXY3):



      A191314E01
    1. Install the idler pulley cover plate, idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      1. If it is necessary to replace the pulley or either plate, replace the No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate as a set with new parts.
      2. When replacing parts, make sure to replace the No. 2 idler pulley with a new pulley marked "PU107013ARMXY3".



  1. w/o Idler Pulley Cover Plate (PU107013ARMXY1):



      A191315E01
    1. Install the idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      1. If it is necessary to replace the pulley or plate, replace both the pulley and plate with a set of new parts that includes a No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate.
      2. When replacing parts, make sure to replace the No. 2 idler pulley with a new pulley marked "PU107013ARMXY3".



20. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A076445E04
  1. Temporarily install the V-ribbed belt tensioner with the 5 bolts.

  1. Install the V-ribbed belt tensioner by tightening bolt 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

    Bolt length:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)



21. INSTALL ENGINE ASSEMBLY
  1. Install the engine assembly to the vehicle (Click here).