Home › ENGINE · 1GR-FE › ENGINE MECHANICAL › CYLINDER HEAD GASKET (for Bank 2)

CYLINDER HEAD GASKET (for Bank 2) > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY
  1. Remove the engine assembly from the vehicle (Click here).



2. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 6 ignition coil connectors.



    A151791
  1. Remove the 6 bolts and 6 ignition coils.



3. REMOVE SPARK PLUG
  1. Remove the 6 spark plugs.



4. REMOVE VVT SENSOR


    G038105
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



5. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


A111700E01
  1. Disconnect the oil control valve connector.

  1. Remove the bolt and oil control valve.

  1. Remove the O-ring from the oil control valve.



6. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH


    A072943E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A072944E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



8. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A158542
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



9. REMOVE HEATER WATER PIPE SUB-ASSEMBLY


    A158634
  1. Remove the 2 bolts and disconnect the 3 water hoses.



10. REMOVE REAR WATER BY-PASS JOINT
  1. Disconnect the engine coolant temperature sensor connector.



    A076534E01
  1. Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.



    A076535E01
  1. Remove the O-ring from the No. 1 water outlet pipe.



11. REMOVE OIL CONTROL VALVE FILTER


    A072942E06
  1. Remove the 2 unions, 2 filters and 2 gaskets from cylinder head LH and RH.



12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A076445E01
  1. Remove the 5 bolts and V-ribbed belt tensioner.



13. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

HINT:
Use the same procedure for both No. 2 idler pulleys.



  1. w/ Idler Pulley Cover Plate:



      A191314E01
    1. Remove the bolt, No. 2 idler pulley cover plate, idler pulley and idler pulley cover plate.



  1. w/o Idler Pulley Cover Plate:



      A191315E01
    1. Remove the bolt, No. 2 idler pulley cover plate and idler pulley.



14. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A158544
  1. Remove the bolt and No. 1 idler pulley.



15. REMOVE CRANKSHAFT PULLEY


    A072945E01
  1. Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.



    G038065E10
  1. Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.



    A072947E03
  1. Using SST, hold the crankshaft pulley and loosen the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)



16. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A151269E01
  1. Remove the 10 bolts and 2 nuts.



    A151270
  1. Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.



17. REMOVE OIL STRAINER SUB-ASSEMBLY


    A151271
  1. Remove the 2 nuts, oil strainer and gasket.



18. REMOVE OIL PAN SUB-ASSEMBLY


    A151272E02
  1. Remove the 17 bolts (A, B, C) and 2 nuts.



    A072953E03
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.



    A076306E01
  1. Remove the O-ring from the cylinder block.



19. DISCONNECT NO. 2 OIL COOLER HOSE


A151242E01


20. DISCONNECT OIL COOLER HOSE


21. REMOVE WATER INLET HOUSING


    A076337E01
  1. Remove the 5 bolts and water inlet housing.

  1. Remove the O-ring and gasket from the water outlet pipe and water pump.



22. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY


    A151244
  1. Remove the 3 bolts, 2 nuts, oil filter bracket and O-ring.



23. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A158566E01
  1. Remove the 24 bolts labeled A and B, and 2 nuts.



    G038102E01
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the cylinder head LH side.



24. REMOVE FRONT CRANKSHAFT OIL SEAL


    A134550E02
  1. If the timing chain case is removed:

    1. Using a screwdriver and wooden block, pry out the oil seal.

      HINT:
      Tape the screwdriver tip before use.

      NOTICE:
      Do not damage the surface of the oil seal press fit hole and crankshaft.



25. SET NO. 1 CYLINDER TO TDC / COMPRESSION


    A076530E01
  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.



    G038065E10
  1. Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.



26. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.



    A158627E01
  1. While turning the stopper plate of the tensioner clockwise, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ 3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts and chain tensioner.



27. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the chain tensioner slipper.



28. REMOVE NO. 1 IDLE GEAR SHAFT


    A072959E01
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.



29. REMOVE NO. 2 CHAIN VIBRATION DAMPER


    G036844E01
  1. Remove the 2 No. 2 chain vibration dampers.



30. REMOVE NO. 1 CHAIN
  1. Remove the No. 1 chain.



31. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A076292E01
  1. Remove the 2 bolts and No. 1 chain vibration damper.



32. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN


    G038075E01
  1. While raising the No. 3 chain tensioner, insert a pin of φ 1.0 mm (0.0394 in.) into the hole to fix it.



    G038112E01
  1. Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing sprocket and No. 2 chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear.



33. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


    A072965E01
  1. Remove the bolt and No. 3 chain tensioner.



34. REMOVE NO. 3 CAMSHAFT AND NO. 4 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.



    A072968E17
  1. Uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 8 bearing caps and 2 camshafts.



35. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH


    A072969E11
  1. Uniformly loosen and remove the 2 cylinder head bolts in the sequence shown in the illustration.



    A076277E02
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.



    A076804E01
  1. Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to lift off, pry between the cylinder head and cylinder block with a screwdriver.



36. REMOVE NO. 2 CYLINDER HEAD GASKET