Home › ENGINE ยท 1GR-FE › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY
  1. Remove the engine assembly from the vehicle (Click here).



2. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 6 ignition coil connectors.



    A151791
  1. Remove the 6 bolts and 6 ignition coils.



3. REMOVE SPARK PLUG
  1. Remove the 6 spark plugs.



4. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A158542
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



5. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A076445E01
  1. Remove the 5 bolts and V-ribbed belt tensioner.



6. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

HINT:
Use the same procedure for both No. 2 idler pulleys.



  1. w/ Idler Pulley Cover Plate:



      A191314E01
    1. Remove the bolt, No. 2 idler pulley cover plate, idler pulley and idler pulley cover plate.



  1. w/o Idler Pulley Cover Plate:



      A191315E01
    1. Remove the bolt, No. 2 idler pulley cover plate and idler pulley.



7. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A158544
  1. Remove the bolt and No. 1 idler pulley.



8. DISCONNECT NO. 2 OIL COOLER HOSE


A151242E01


9. DISCONNECT OIL COOLER HOSE


10. REMOVE WATER INLET HOUSING


    A076337E01
  1. Remove the 5 bolts and water inlet housing.

  1. Remove the O-ring and gasket from the water outlet pipe and water pump.



11. REMOVE VVT SENSOR


    G038105
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



12. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A158547E02
  1. Remove the 2 bolts and 2 camshaft timing oil control valves from the cylinder head LH and RH.

  1. Remove the 2 O-rings.



13. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH


    A072943E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



14. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A072944E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



15. REMOVE CRANKSHAFT PULLEY


    A072945E01
  1. Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.



    G038065E10
  1. Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.



    A072947E03
  1. Using SST, hold the crankshaft pulley and loosen the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)



16. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A151269E01
  1. Remove the 10 bolts and 2 nuts.



    A151270
  1. Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.



17. REMOVE OIL STRAINER SUB-ASSEMBLY


    A151271
  1. Remove the 2 nuts, oil strainer and gasket.



18. REMOVE OIL PAN SUB-ASSEMBLY


    A151272E02
  1. Remove the 17 bolts (A, B, C) and 2 nuts.



    A072953E03
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.



    A076306E01
  1. Remove the O-ring from the cylinder block.



19. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY


    A151244
  1. Remove the 3 bolts, 2 nuts, oil filter bracket and O-ring.



20. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A158566E01
  1. Remove the 24 bolts (A and B) and 2 nuts.



    G038102E01
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the cylinder head LH.



21. REMOVE FRONT CRANKSHAFT OIL SEAL


    A134550E02
  1. If the timing chain case is removed:

    1. Using a screwdriver and wooden block, pry out the oil seal.

      HINT:
      Tape the screwdriver tip before use.

      NOTICE:
      Do not damage the surface of the oil seal press fit hole and crankshaft.