Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2171/71    Transmitter ID not Registered

for Preparation Click here


DESCRIPTION

The transmitter IDs of each tire pressure warning valve and transmitter are registered to the tire pressure warning ECU.
When the IDs have never been registered, a DTC is output.

DTC Code
DTC Detection Condition
Trouble Area
C2171/71
Transmitter ID is not registered. (When a transmitter ID is unregistered for 3 minutes or more)
Tire pressure warning ECU

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and note them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.

1.CONFIRM REGISTRATION CONDITION (REGISTERED TRANSMITTER IDS)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Registered ID1 Code
    Registered ID1 code/
    min.: 0
    max.: FFFFFFFF*
    The transmitter ID registered in the transmitter ID1 is displayed
    *: Displayed only when the transmitter ID is not registered.
    Registered ID2 Code
    Registered ID2 code/
    min.: 0
    max.: FFFFFFFF*
    The transmitter ID registered in the transmitter ID2 is displayed
    *: Displayed only when the transmitter ID is not registered.
    Registered ID3 Code
    Registered ID3 code/
    min.: 0
    max.: FFFFFFFF*
    The transmitter ID registered in the transmitter ID3 is displayed
    *: Displayed only when the transmitter ID is not registered.
    Registered ID4 Code
    Registered ID4 code/
    min.: 0
    max.: FFFFFFFF*
    The transmitter ID registered in the transmitter ID4 is displayed
    *: Displayed only when the transmitter ID is not registered.

    OK:
    The registered transmitter IDs are displayed on the Techstream screen.



NG
Go to step 2
OK

REPLACE TIRE PRESSURE WARNING ECU (Click here)  

2.PERFORM REGISTRATION (TRANSMITTER ID)
  1. Register the transmitter IDs for all the wheels (Click here).


NEXT


3.PERFORM INITIALIZATION
  1. Perform initialization (Click here).


NEXT


4.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure / 100 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*

    HINT:
    1. *: It may take about 5 to 6 minutes until the values are displayed.
    2. When no "ID Tire Inflation Pressure" has changed, rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.


    Result 
    Result
    Proceed to
    Tire pressure values are not displayed.
    A
    All tire pressure readings are equal to specified values.
    B



B
END
A

REPLACE TIRE PRESSURE WARNING ECU (Click here)