Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0607    Control Module Performance

for Preparation Click here


DESCRIPTION

The ECM continuously monitors its internal processors (CPUs), heated oxygen sensor (HO2S) transistors. This self-check ensures that the ECM is functioning properly. This is diagnosed by internal "mirroring" of the main and sub CPUs to detect processor errors. If outputs from the processors deviate from the standard, the ECM will illuminate the MIL and set a DTC immediately.

DTC Code
DTC Detection Condition
Trouble Area
P0607
  1. ECM CPUs malfunction
  2. HO2S transistors malfunction
  1. Exhaust gas leak
  2. HO2S
  3. ECM

MONITOR STRATEGY


Related DTCs
P0607: Control module performance
Required sensors/Components (Main)
ECM
Required sensors/Components (Related)
APP sensor, TP sensor, Stop light switch, Cruise control, HO2S
Frequency of operation
Continuous
Duration
60 seconds
MIL operation
immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not present
None
Engine
Running
Estimated HO2S temperature
450 to 800°C (842 to 1472°F)

TYPICAL MALFUNCTION THRESHOLDS


HO2S transistors
Fail

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTC (Click here).
    Result 
    Result
    Proceed to
    P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output
    A
    P0607 is output
    B



B
Go to step 3
A


2.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flow chart.

    HINT:
    1. If P0136 or P0156 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
    2. If P0137 or P0157 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
    3. If P0138 or P0158 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
    4. If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).



NEXT
Go to step 6

3.CHECK FOR EXHAUST GAS LEAK
  1. Allow the engine to idle and rev the engine.

  1. Check for exhaust gas leaks around the heated oxygen sensor.
    If any exhaust gas leaks are present, repair it and proceed to "PERFORM CONFIRMATION DRIVING PATTERN". If no exhaust gas leaks are present proceed to "PERFORM CONFIRMATION DRIVING PATTERN".

    HINT:
    1. If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is suspected.
    2. If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.


NEXT


4.PERFORM CONFIRMATION DRIVING PATTERN

A144392E23

  1. Clear DTC (Click here).

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Warm up the engine until the engine coolant temperature becomes 75°C (167°F) or more.

  1. Perform the drive pattern.

    1. Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.

    2. Drive the vehicle between 60 and 80 km/h (35 and 50 mph) for 5 minutes.

  1. Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output
    A
    Only P0607
    B
    No DTC output
    C



B
REPLACE ECM (Click here)

C
Go to step 6
A


5.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flow chart.

    HINT:
    1. If P0136 or P0156 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
    2. If P0137 or P0157 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
    3. If P0138 or P0158 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
    4. If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).


NEXT


6.INSPECT ECM
  1. Clear DTC (Click here).

  1. Stop the engine and wait for 30 minutes.

  1. Connect the Techstream to the DLC3.

  1. Start the engine and allow it to idle for 2 minutes.

  1. Turn the Techstream on.

  1. Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.

  1. Check the DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    P0607 is output
    B



B
REPLACE ECM (Click here)
A

END