VACUUM SWITCHING VALVE (for ACIS) > INSTALLATION |
| 1. INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS) |
Connect the VSV connector.
![]() |
Install the VSV connector and VSV to the intake manifold with the 2 bolt.
Connect the 2 vacuum hoses to the VSV.
| 2. INSTALL INTAKE MANIFOLD |
![]() |
Place 2 new gaskets on the intake manifold.
Place the intake manifold on the cylinder heads.
![]() |
Install and uniformly tighten the 6 bolts and 4 nuts in several steps.
![]() |
Install the engine wire protector with the 2 bolts.
Connect the 8 injector connectors.
![]() |
Connect the 2 wire clamps to the wire clamp brackets on the RH delivery pipe.
![]() |
Connect the VSV connector (for ACIS).
![]() |
Install the wire bracket to the intake manifold with the bolt.
Connect the engine wire to the wire bracket and engine hanger.
![]() |
Connect the purge line hose to the purge VSV.
Connect the purge VSV connector.
![]() |
Connect the No. 1 ventilation hose to the ventilation valve on the LH cylinder head.
![]() |
Connect the 2 water by-pass hoses to the throttle body.
Connect the throttle position sensor and control motor connector.
| 3. INSTALL FUEL MAIN TUBE |
![]() |
Connect the fuel main tube (Click here).
Install the fuel pipe clamp.
| 4. INSTALL FUEL RETURN TUBE |
![]() |
Connect the fuel return tube (Click here).
| 5. INSTALL NO. 2 WATER BY-PASS PIPE |
![]() |
Connect the 2 hoses to the water by-pass pipe.
Install the No. 2 water by-pass pipe with the 2 bolts.
![]() |
Connect the 2 water hoses.
| 6. INSTALL NO. 1 BRAKE BOOSTER TUBE |
![]() |
Connect the hose to the intake manifold.
Install the vacuum hose assembly with the bolt.
| 7. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose.
Connect the vacuum hose and No. 2 ventilation hose.
| 8. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines. If the coolant level is below the LOW line, repeat all of the procedures above. If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 9. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 10. CHECK FOR FUEL LEAK |
![]() |
Install a new grommet to each injector.
Apply a light coat of gasoline to each new O-ring and install one to each injector.
![]() |
Install the 8 injectors.
While turning each injector clockwise and counterclockwise, push it onto the delivery pipes.
Position the injector connectors outward.
Place 8 new insulators on the intake manifold.
| 11. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover onto the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 12. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY |
![]() |
Install the 2 throttle body cover brackets with the 2 bolts.
![]() |
Install the throttle body cover with the 2 cap nuts.
| 13. INSTALL FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY |
Install the outer panel with the 7 bolts.

Connect the 2 washer hoses.
| 14. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY |
For the front wiper motor and link, refer to the following procedures (Click here).
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |