VACUUM SWITCHING VALVE (for ACIS) > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the 2 fuel pump ECU connectors.
Connect the cable to the negative (-) battery terminal.
Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.
Crank the engine again, then check that the engine does not start.
Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.
Connect the 2 fuel pump ECU connectors.
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 3 screws and 5 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
| 4. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.
Remove the radiator cap. Then drain the coolant.
Tighten the 2 cylinder block drain cock plugs.

Tighten the radiator drain cock plug by hand.
| 5. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY |
For the front wiper motor and link, refer to the following procedures (Click here).
| 6. REMOVE FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY |
Disconnect the 2 washer hoses.
Remove the 7 bolts and outer panel.

| 7. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY |
![]() |
Remove the 2 cap nuts and throttle body cover.
![]() |
Remove the 2 bolts and 2 throttle body cover brackets from the intake manifold.
| 8. REMOVE AIR CLEANER HOSE ASSEMBLY |
![]() |
Disconnect the vacuum hose and No. 2 ventilation hose.
Loosen the 2 hose clamps.
Remove the air cleaner hose.
| 9. REMOVE VACUUM HOSE ASSEMBLY |
![]() |
Remove the bolt and disconnect the vacuum hose assembly.
| 10. REMOVE NO. 2 WATER BY-PASS PIPE |
![]() |
Disconnect the 2 water hoses from the No. 2 water by-pass pipe.
![]() |
Remove the 2 bolts.
Remove No. 2 water by-pass pipe together with the water hose.
| 11. REMOVE FUEL RETURN TUBE |
![]() |
Disconnect the fuel return tube (Click here).
| 12. REMOVE FUEL MAIN TUBE |
![]() |
Remove the fuel pipe clamp.
Disconnect the fuel main tube (Click here).
| 13. REMOVE INTAKE MANIFOLD |
![]() |
Disconnect the throttle position sensor and control motor connector.
Disconnect the 2 water by-pass hoses from the throttle body.
![]() |
Disconnect the No. 1 ventilation hose from the ventilation valve on the LH cylinder head.
![]() |
Disconnect the purge VSV connector.
Disconnect the purge line hose from the purge VSV.
![]() |
Disconnect the VSV connector.
![]() |
Disconnect the 2 wire clamps from the wire bracket and engine hanger.
Remove the bolt and wire bracket from the intake manifold.
![]() |
Disconnect the 2 wire clamps from the wire clamp bracket on the RH delivery pipe.
Disconnect the 8 injector connectors.
![]() |
Remove the 2 bolts and disconnect the engine wire protector.
![]() |
Remove the 6 bolts, 4 nuts, intake manifold and 2 gaskets.
| 14. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS) |
![]() |
Disconnect the 2 vacuum hoses.
Remove the 2 bolt, VSV connector and VSV from the intake manifold.
Disconnect the VSV connector.