Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD (for Floor Shift Type)

INSTRUMENT PANEL SAFETY PAD (for Floor Shift Type) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL NO. 3 INSTRUMENT PANEL STAY


  1. Attach the 5 claws to install the 5 stays.


    B161139



2. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Attach the 5 claws to install the instrument panel.

  1. Install the 3 bolts and 2 nuts.



  1. Install the 2 passenger airbag bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    B163939

  1. Connect the connectors and attach the connectors to the clamps.



  1. Install the wire harness with the bolt.


    B161138



3. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD INSERT


    B160602
  1. Connect the connector.

  1. Attach the 2 claws to install the safety pad.

  1. Install the 4 bolts.



4. INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (for 10 Speaker Models)


B165751E01
  1. Connect the connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



5. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161134
  1. Attach the 6 clips and 2 claws to install the speaker panel.



6. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH
  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



7. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161135
  1. Attach the 4 clips and claw to install the speaker panel.



8. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH



B165750E01

  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



9. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161136
  1. Attach the 4 clips and claw to install the speaker panel.



10. INSTALL GLOVE BOX LIGHT ASSEMBLY


    B161133
  1. Connect the connector.

  1. Attach the 2 claws to install the box light.



11. INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    B160592
  1. Install the box door with the 6 screws.



    B160591
  1. Attach the 4 claws to install the 2 instrument panel hole covers.



12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B160593
  1. Attach the 3 claws to install the finish panel.

  1. Install the 3 screws.

  1. Install the bolt.



13. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab)


15. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab, CrewMax)


16. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



17. INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab)

HINT:
Use the same procedures described for the LH side.



18. INSTALL FRONT DOOR SCUFF PLATE RH (for Double Cab, CrewMax)

HINT:
Use the same procedures described for the LH side.



19. INSTALL INSTRUMENT SIDE PANEL RH


    B163940
  1. Attach the 6 claws to install the side panel.



20. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


B165758
  1. Connect the connectors.

  1. Insert the navigation receiver as shown in the illustration to attach the 3 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    B164792
  1. Install the navigation receiver with the 4 bolts.



21. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET


B166274
  1. Connect the connectors.

  1. Insert the radio receiver and attach the 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver, do not press its knobs.



    B164786
  1. Install the radio receiver with the 4 bolts.



22. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning System)


    B160589
  1. Connect the connectors.

  1. Attach the 4 clips to install the panel.



23. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air Conditioning System)


    B160588
  1. Connect the connectors.

  1. Attach the 4 clips to install the panel.



24. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B161747
  1. Connect the connectors.

  1. Attach the 4 clips to install the finish panel.



25. INSTALL COMBINATION METER ASSEMBLY


    B160584
  1. Connect the connector and clamp.

  1. Install the combination meter with the 4 screws.



26. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B164474
  1. Attach the 12 clips to install the finish panel.

  1. Connect the connector and clamp.



27. INSTALL FRONT CONSOLE BOX


    B161746
  1. Install the front console box with the 6 screws and 2 clips.



28. INSTALL REAR CONSOLE BOX ASSEMBLY


    B161745
  1. Install the rear console box with the 2 screws and 4 bolts.



29. INSTALL CONSOLE BOX CARPET
  1. Install the carpet.



30. INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY


    B161744
  1. except Regular Cab:
    Connect the connector.

  1. Attach the 7 clips to install the end panel.



31. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. w/ Trailer Towing System:
    Connect the connector.

  1. Attach the 6 clips to install the console panel.



  1. Install the clip.


    B171298



32. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Attach the 12 clips to install the console panel.



33. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B167312
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



34. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. for Automatic Air Conditioning System:
    Attach the 2 claws to install the sensor.



    B168286
  1. Connect the connectors.

  1. Attach the 4 clips and claw to install the finish panel.

  1. Install the 2 bolts.

  1. Install the hood lock control lever.



35. INSTALL INSTRUMENT SIDE PANEL LH


    B163942
  1. Attach the 7 claws to install the side panel.



36. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab)


37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab, CrewMax)


38. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165706



39. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



40. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)


B165843
  1. Attach the 6 claws and 3 clips to install the scuff plate.



41. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)


B165841
  1. Attach the 6 claws and 3 clips to install the scuff plate.



42. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


C159216
  1. Install the turn signal switch assembly with spiral cable to the steering column assembly with the clamp.



    C154522
  1. Connect the 5 connectors to the turn signal switch with spiral cable.



43. INSTALL TILT AND TELESCOPIC MANUAL SWITCH (for Power Tilt and Power Telescopic Steering Column)


C159804
  1. Attach the claw to install the tilt and telescopic switch.

  1. Connect the connector.



44. INSTALL UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)


C159215
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



45. INSTALL UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)


C159215
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



46. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)


C154519
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



47. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)


C154519
  1. Attach the 2 claws to install the column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



48. INSTALL STEERING WHEEL ASSEMBLY


C159526E01
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



49. INSTALL STEERING PAD (w/o Steering Pad Switch)


    B166435
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel.

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



50. INSTALL STEERING PAD (w/ Steering Pad Switch)


    B166581
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel .

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



51. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Attach the 2 claws to install the cover.



52. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. w/ Cruise Control:

    1. Attach the 2 claws to install the cover.



    B167059
  1. w/o Cruise Control:

    1. Attach the 2 claws to install the cover.



53. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



54. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).