Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short in CAN Bus Lines

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. Combination meter ECU
  3. Main body ECU
  4. Skid control ECU with actuator
  5. Steering angle sensor
  6. Center airbag sensor
  7. Bus buffer ECU*1
  8. Air conditioning amplifier
  9. ECM
  10. 4WD control ECU*2
  11. No. 1 junction connector
  12. No. 2 junction connector

HINT:
  1. *1: w/ Bus buffer ECU
  2. *2: w/ 4WD


WIRING DIAGRAM


C158942E01


C158943E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.


NEXT


2.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)


    H102392E70
  1. Disconnect the J86 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J17-6 (CANH) - J17-14 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CONNECT CONNECTOR
  1. Reconnect the J86 No. 1 junction connector connector.


NEXT


4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR)


    H102392E70
  1. Disconnect the J93 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    J17-6 (CANH) - J17-14 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
Go to step 17
OK


5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C159609E01
  1. Disconnect the J94 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J94-1 (CANH) - J94-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


6.CONNECT CONNECTOR
  1. Reconnect the J94 No. 1 junction connector connector.

  1. Reconnect the J93 No. 2 junction connector connector.


NEXT


7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C137766E66
  1. Disconnect the J84 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J84-1 (CANH) - J84-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 12
OK


8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    C159609E05
  1. Disconnect the J96 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J96-1 (CANH) - J96-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 13
OK


9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU WITH ACTUATOR)


    C137766E67
  1. Disconnect the A46 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    A46-1 (CANH) - A46-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 14
OK


10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C159609E06
  1. Disconnect the J87 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J87-1 (CANH) - J87-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 15
OK


11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)


    C137766E68
  1. Disconnect the J83 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J83-1 (CANH) - J83-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 16
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR 

12.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU)


    C137766E66
  1. Disconnect the J28 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J84-1 (CANH) - J84-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY  

13.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159609E05
  1. Disconnect the J2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J96-1 (CANH) - J96-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU 

14.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU WITH ACTUATOR)


    C137766E67
  1. Disconnect the A17 skid control ECU with actuator connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    A46-1 (CANH) - A46-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU WITH ACTUATOR (CANH, CANL)
OK

REPLACE SKID CONTROL ECU WITH ACTUATOR (Click here)  

15.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)


    C159609E06
  1. Disconnect the J6 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J87-1 (CANH) - J87-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR  

16.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR)


    C137766E68
  1. Disconnect the J46 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J83-1 (CANH) - J83-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR  

17.CONNECT CONNECTOR
  1. Reconnect the J93 No. 2 junction connector connector.


NEXT


18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)


    C159609E07
  1. Disconnect the J85 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J85-1 (CANH) - J85-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 22
OK


19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)

NOTICE:
For vehicles without bus buffer ECU, go to "CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)".



    C159609E08
  1. Disconnect the J98 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J98-1 (CANH) - J98-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 23
OK


20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without 4WD, go to "CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - ECM)".



    C159609E09
  1. Disconnect the J88 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J88-1 (CANH) - J88-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 24
OK


21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - ECM)


    C159609E10
  1. Disconnect the J92 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J92-1 (CANH) - J92-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 25
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR 

22.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER)


    C159609E07
  1. Disconnect the J19 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J85-1 (CANH) - J85-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY  

23.CHECK FOR SHORT IN CAN BUS WIRES (BUS BUFFER ECU)


    C159609E08
  1. Disconnect the J59 bus buffer ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J98-1 (CANH) - J98-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CANH, CANL)
OK

REPLACE BUS BUFFER ECU 

24.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)


    C159609E09
  1. Disconnect the A25 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J88-1 (CANH) - J88-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4WD CONTROL ECU  

25.CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    C159609E10
  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Result
    Proceed to
    J92-1 (CANH) - J92-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK (for 1GR-FE)
    A
    OK (for 2UZ-FE)
    B
    OK (for 3UR-FE)
    C
    OK (for 3UR-FBE)
    D
    Below 1 Ω
    NG
    E



B
REPLACE ECM

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM