CAN COMMUNICATION SYSTEM > Open in One Side of CAN Branch Line |
| Symptom | Trouble Area |
| 2 or more ECUs and/or sensors do not appear on Techstream "CAN Bus Check" screen. |
|


| 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
| NEXT | |
| 2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU) |
Disconnect the J2 main body ECU connector.
Reconnect the cable to the negative (-) battery terminal.
Select "CAN Bus Check" on the Techstream.
| Result | Proceed to |
| Main Body not displayed on Techstream. | A |
| Several ECUs and sensors other than Main Body not displayed on Techstream. | B |
|
| ||||
| A | |
| 3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J2-5 (CANH) - J2-6 (CANL) | Ignition switch OFF | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU WITH ACTUATOR) |
Disconnect the A17 skid control ECU with actuator connector.
Reconnect the cable to the negative (-) battery terminal.
Select "CAN Bus Check" on the Techstream.
| Result | Proceed to |
| ABS/VSC/TRAC not displayed on Techstream. | A |
| Several ECUs and sensors other than ABS/VSC/TRAC not displayed on Techstream. | B |
|
| ||||
| A | |
| 5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU WITH ACTUATOR BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A17-5 (CANH) - A17-4 (CANL) | Ignition switch OFF | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR) |
Disconnect the J6 steering angle sensor connector.
Reconnect the cable to the negative (-) battery terminal.
Select "CAN Bus Check" on the Techstream.
| Result | Proceed to |
| Steering Angle Sensor not displayed on Techstream. | A |
| Several ECUs and sensors other than Steering Angle Sensor not displayed on Techstream. | B |
|
| ||||
| A | |
| 7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J6-10 (CANH) - J6-9 (CANL) | Ignition switch OFF | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU) |
Disconnect the J59 bus buffer ECU connector.
Reconnect the cable to the negative (-) battery terminal.
Select "CAN Bus Check" on the Techstream.
| Result | Proceed to |
| Accessory Gateway not displayed on Techstream. | A |
| Several ECUs and sensors other than Accessory Gateway not displayed on Techstream. | B |
|
| ||||
| A | |
| 9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J59-3 (CAN+) - J59-2 (CAN-) | Ignition switch OFF | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR) |
Disconnect the J46 center airbag sensor connector.
Reconnect the cable to the negative (-) battery terminal.
Select "CAN Bus Check" on the Techstream.
| Result | Proceed to |
| SRS Airbag not displayed on Techstream. | A |
| Several ECUs and sensors other than SRS Airbag not displayed on Techstream. | B |
|
| ||||
| A | |
| 11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J46-13 (CANH) - J46-22 (CANL) | Ignition switch OFF | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU) |
Disconnect the A25 4WD control ECU connector.
Reconnect the cable to the negative (-) battery terminal.
Select "CAN Bus Check" on the Techstream.
| Result | Proceed to |
| Four Wheel Drive Control not displayed on Techstream. | A |
| Several ECUs and sensors other than Four Wheel Drive Control not displayed on Techstream. | B |
|
| ||||
| A | |
| 13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A25-19 (CANH) - A25-20 (CANL) | Ignition switch OFF | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE) |
![]() |
Disconnect the J19 air conditioning amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J19-11 (CANH) - J19-12 (CANL) | Ignition switch OFF | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||