Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > Air Conditioning Compressor Magnetic Clutch Circuit

for Preparation Click here


DESCRIPTION

When the air conditioning amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the air conditioning amplifier. Then, the magnetic clutch relay (MG CLT) turns on to operate the magnetic clutch.

WIRING DIAGRAM


E146216E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (A/C SIGNAL)
  1. Use the Data List to check if the air conditioning signal is functioning properly.

    ECM 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    Air conditioning switch signal /
    ON or OFF
    ON: Air conditioning ON
    OFF: Air conditioning OFF
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (A/C IG)
  1. Remove the A/C IG fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A/C IG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.INSPECT MAGNETIC CLUTCH RELAY (MG CLT)
B060778E04
  1. Remove the magnetic clutch relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied between terminals
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE MAGNETIC CLUTCH RELAY
OK


4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
E146413E02
  1. Disconnect the J19 air conditioning amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-20 (MGC) - Body ground
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK AIR CONDITIONING AMPLIFIER (MGC VOLTAGE)
E146409E03
  1. Reconnect the J19 air conditioning amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-20 (MGC) - Body ground
    Engine running and air conditioning switch ON
    Below 1 V
    Engine running and air conditioning switch OFF
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK


6.INSPECT AIR CONDITIONING COMPRESSOR (COMPRESSOR HARNESS)
E146414E01
  1. Disconnect the D60 air conditioning compressor connector.

  1. Disconnect the magnetic clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (MG+) - 1
    Always
    Below 1 Ω
    3 (MG+) or 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR AIR CONDITIONING COMPRESSOR
OK


7.INSPECT MAGNETIC CLUTCH


    E146516E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Always
    3.4 to 3.8 Ω

  1. When connector terminal 1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound can be heard, and 2) the magnetic clutch's hub and rotor lock.
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2UZ-FE)
    B
    NG (for 3UR-FE or 3UR-FBE)
    C



B
REPLACE MAGNETIC CLUTCH (Click here)

C
REPLACE MAGNETIC CLUTCH (Click here)
A


8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING COMPRESSOR - ENGINE ROOM RELAY BLOCK)
E146415E01
  1. Disconnect the D60 air conditioning compressor connector.

  1. Remove the magnetic clutch relay (MG CLT) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D60-3 (MG+) - Engine room relay block magnetic clutch relay terminal 3
    Always
    Below 1 Ω
    D60-3 (MG+) or Engine room relay block magnetic clutch relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)
E146416E01
  1. Remove the magnetic clutch relay (MG CLT) from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block magnetic clutch relay terminal 5 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)