Home › BODY › INTERIOR › ROOF HEADLINING (for Double Cab)

ROOF HEADLINING (for Double Cab) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. PLACE ROOF HEADLINING ASSEMBLY


B166622
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    1. Place the headlining in the cabin so that it will not be damaged.
    2. Be careful not to damage the roof headlining when placing it in the cabin.



2. INSTALL BACK WINDOW ASSEMBLY


B166487E01
  1. Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Using a brush or sponge, apply Primer G to the contact surface of the back window.


    B166488E01



    B166489E01

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the back window.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration below.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back window as shown in the illustration.


      B166490E01



      B166491E01

      Standard measurement:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)



    B166485
    B166484E01
  1. Using suction cups, position the glass so that the reference marks are aligned. Press it in gently along the rim.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Check that the clips are attached to the vehicle body correctly.
    3. Check the clearance between the vehicle body and glass.

  1. Lightly press the front surface of the back window to ensure that the back window is securely fit to the vehicle body.

    NOTICE:
    Check that the spacers are attached to the vehicle body correctly.

  1. Using a scraper, remove any excess or protruding adhesive.

    NOTICE:
    Do not drive the vehicle within the time written in the table below.

    Minimum time:
    Temperature
    Minimum time prior to driving vehicle
    35°C (95°F)
    1 hour 30 minutes
    20°C (68°F)
    5 hours
    5°C (41°F)
    24 hours



3. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



4. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. If reusing the moulding:
    Clean the moulding.

    1. Using a heat light, heat the moulding.

    2. Remove the double-sided tape from the moulding.

    3. Wipe off any tape adhesive residue with cleaner.



    4. B163286E01
    5. Apply new double-sided tape to the moulding, as shown in the illustration.



  1. Install the moulding.

    1. Using a heat light, heat the vehicle body and moulding.

    2. Remove the peeling paper from the face of the moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.



    3. B163282E03
    4. Attach the clip to install the moulding.

      HINT:
      Press the moulding firmly to install it.



5. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT:
Use the same procedures described for the LH side.



6. INSTALL ROOF HEADLINING ASSEMBLY


  1. Attach the 4 clips to install the headlining.


    B165846E03



    B165723
  1. Connect the roof wire connector and attach each clamp.



    B167283
  1. w/ EC Mirror:

    1. Connect the EC mirror connector.



    2. B166359
    3. Attach the 2 claws to install the inner rear view mirror cover.



7. INSTALL COAT HOOK


B168150

HINT:
Use the same procedure to install the coat hook on the other side.

  1. Install the clip and cap to the coat hook, as shown in the illustration.

  1. Install the coat hook.



8. INSTALL ASSIST GRIP PLUG


B165717
  1. Install a new assist grip plug.



9. INSTALL ASSIST GRIP SUB-ASSEMBLY


B165740
  1. Install the 2 clips and 2 covers to the assist grip, as shown in the illustration.

  1. Install the assist grip.



10. INSTALL VISOR HOLDER (w/o Illumination)


B165713
  1. Install the visor holder with the screw.

    HINT:
    Use the same procedure to install the visor holder on the other side.



11. INSTALL VISOR ASSEMBLY LH


B165715
  1. w/o Illumination:
    Install the visor.

    1. Install the visor with the 3 screws.



    B165840
  1. w/ Illumination:
    Install the visor.

    1. Connect the connector.

    2. Install the visor with the 4 screws.



12. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



13. INSTALL VISOR BRACKET COVER LH


B166262
  1. Attach the 4 claws to install the visor bracket cover.



14. INSTALL VISOR BRACKET COVER RH

HINT:
Use the same procedures described for the LH side.



15. INSTALL ROOM LIGHT ASSEMBLY (w/ Short Type Roof Console Box)
  1. Connect the connector.

  1. Attach the 4 clips to install the room light.



  1. Attach the 4 claws to install the lens.


    B165837



16. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Install the roof console box .

  1. for Long Type:
    Install the roof console box .



17. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH


B165833
  1. Pass the rear seat outer belt floor anchor through the quarter trim panel.

  1. Attach the 4 clips to install the quarter trim panel.

  1. Install the 2 bolts.



    B165712
  1. Attach the claw to install the cover.



18. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



19. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH


B165832
  1. Attach the 6 clips to install the quarter trim panel.



    B165831
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165830
  1. Attach the 2 claws to install the cover.



20. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



21. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B166614
  1. Slide the plate in the direction shown in the illustration and attach the 6 claws to install the plate.



22. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



23. INSTALL CENTER PILLAR GARNISH LH
  1. Pass the front seat outer belt floor anchor through the center pillar garnish.

  1. Attach the claw to install the center pillar garnish.

  1. Install the 2 screws.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165826



24. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



25. INSTALL LOWER CENTER PILLAR GARNISH LH


B165829
  1. Attach the 7 clips and 2 claws to install the center pillar garnish.



    B165828
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165827
  1. Attach the 2 claws to install the cover.



26. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



27. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165706



28. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



29. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


30. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


32. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


33. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



34. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



35. INSTALL REAR DOOR SCUFF PLATE LH


B165842
  1. Attach the 6 claws and 2 clips to install the scuff plate.



36. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



37. INSTALL FRONT DOOR SCUFF PLATE LH


B165841
  1. Attach the 6 claws and 3 clips to install the scuff plate.



38. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



39. INSTALL REAR SEAT ASSEMBLY (for Double Cab)
  1. Install the rear seat (Click here).



40. INSTALL FRONT SEAT ASSEMBLY (for Center Seat)
  1. Install the front seat (Click here).



41. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Install the front seat (Click here).



42. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
  1. Install the front seat (Click here).



43. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



44. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).