Home › BODY › MIRROR › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch

for Preparation Click here


SYSTEM DESCRIPTION

The circuit detects the conditions of the outer mirror switch.
The outer mirror switch sends information about the operating condition of the mirror switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU. Mirror adjustment is controlled by the outer mirror control ECU.

WIRING DIAGRAM


B166096E02


INSPECTION PROCEDURE

1.CHECK DTC
  1. Use the Techstream to check if the CAN communication system is functioning normally (Click here).
    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.READ VALUE USING TECHSTREAM (OUTER MIRROR SWITCH)
  1. Check the DATA LIST for proper functioning of the outer mirror switch.

    Main body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror selection SW (Right)
    Mirror master switch signal for RH mirror / ON or OFF
    ON: Switch is in R position
    OFF: Switch is OFF or in L position
    -
    Mirror position SW (Right)
    Mirror control switch signal (RIGHT) / ON or OFF
    ON: RIGHT switch is ON
    OFF: Any switch except RIGHT is ON or all switches are OFF
    -
    Mirror position SW (Left)
    Mirror control switch signal (LEFT) / ON or OFF
    ON: LEFT switch is ON
    OFF: Any switch except LEFT is ON or all switches are OFF
    -
    Mirror position SW (UP)
    Mirror control switch signal (UP) / ON or OFF
    ON: UP switch is ON
    OFF: Any switch except UP is ON or all switches are OFF
    -
    Mirror position SW (Down)
    Mirror control switch signal (DOWN) / ON or OFF
    ON: DOWN switch is ON
    OFF: Any switch except DOWN is ON or all switches are OFF
    -

    OK:
    On screen, each item changes between ON and OFF according to above chart.



NG
Go to step 5
OK


3.INSPECT OUTER REAR VIEW MIRROR RH


    B166615E01
  1. Remove the mirror RH (Click here).

  1. Apply battery voltage and check the operation of the power mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 10 (MV)
    Battery negative (-) → Terminal 11 (M+)
    Turns upward (A)
    Battery negative (-) → Terminal 10 (MV)
    Battery positive (+) → Terminal 11 (M+)
    Turns downward (B)
    Battery positive (+) → Terminal 12 (MH)
    Battery negative (-) → Terminal 11 (M+)
    Turns left (C)
    Battery negative (-) → Terminal 12 (MH)
    Battery positive (+) → Terminal 11 (M+)
    Turns right (D)



NG
REPLACE OUTER REAR VIEW MIRROR RH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)


    B166860E02
  1. Disconnect the N8 ECU connector.

  1. Disconnect the M6 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N8-38 (M+R) - M6-11 (M+)
    Always
    Below 1 Ω
    N8-39 (MHR) - M6-12 (MH)
    N8-40 (MVR) - M6-10 (MV)
    M6-11 (M+) - Body ground
    Always
    10 kΩ or higher
    M6-12 (MH) - Body ground
    M6-10 (MV) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU  

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY


    B167772E01
  1. Remove the switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (M+) - 2 (E)
    UP switch pushed
    100 Ω
    DOWN switch pushed
    470 Ω
    LEFT switch pushed
    800 Ω
    RIGHT switch pushed
    250 Ω
    1 (MSW) - 2 (E)
    No switches pushed
    10 kΩ or higher
    R switch pushed
    Below 1 Ω



NG
REPLACE OUTER MIRROR SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)


    B166955E01
  1. Disconnect the J4 ECU connector.

  1. Disconnect the L6 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J4-2 (MIRE) - L6-2 (E)
    Always
    Below 1 Ω
    J4-11 (MIRB) - L6-3 (M+)
    J4-12 (MIRS) - L6-1 (MSW)
    L6-2 (E) - Body ground
    Always
    10 kΩ or higher
    L6-3 (M+) - Body ground
    L6-1 (MSW) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU