Home › ENGINE ยท 2UZ-FE › INTAKE › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. Some systems need to be initialized after the cable is reconnected (Click here).
    2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



    A159706
  1. Disconnect the 2 fuel pump ECU connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the 2 fuel pump ECU connectors.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and setting. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal
  2. Some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
  1. For the front wiper motor and link, refer to the following procedures (Click here).



4. REMOVE FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the 2 washer hoses.



  1. Remove the 7 bolts and outer panel.


    A151796



5. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



    A156211E01

  1. Tighten the radiator drain cock plug by hand.



7. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY


    A156183E01
  1. Remove the 2 cap nuts and throttle body cover.



    A156184E02
  1. Remove the 2 bolts and 2 throttle body cover brackets from the intake manifold.



8. REMOVE AIR CLEANER HOSE ASSEMBLY


    A153487
  1. Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.



9. REMOVE VACUUM HOSE ASSEMBLY


    A191537
  1. Remove the bolt and disconnect the vacuum hose assembly.



10. REMOVE NO. 2 WATER BY-PASS PIPE


    A191538
  1. Disconnect the 2 water hoses from the No. 2 water by-pass pipe.



    A191539
  1. Remove the 2 bolts.

  1. Remove No. 2 water by-pass pipe together with the water hose.



11. DISCONNECT FUEL RETURN TUBE


    A160926
  1. Disconnect the fuel return tube (Click here).



12. DISCONNECT FUEL MAIN TUBE


    A160925
  1. Remove the fuel pipe clamp.

  1. Disconnect the fuel main tube (Click here).



13. REMOVE INTAKE MANIFOLD ASSEMBLY


    A156170
  1. Disconnect the throttle position sensor and control motor connector.

  1. Disconnect the 2 water by-pass hoses from the throttle body.



    A191540E01
  1. Disconnect the No. 1 ventilation hose from the ventilation valve on the LH cylinder head.



    A156171
  1. Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.



    A163715
  1. Disconnect the VSV connector.



    A156174E02
  1. Disconnect the 2 wire clamps from the wire bracket and engine hanger.

  1. Remove the bolt and wire bracket from the intake manifold.



    A163553
  1. Disconnect the 2 wire clamps from the wire clamp bracket on the RH delivery pipe.

  1. Disconnect the 8 injector connectors.



    A156173
  1. Remove the 2 bolts and disconnect the engine wire protector.



    A156172
  1. Remove the 6 bolts, 4 nuts, intake manifold and 2 gaskets.



14. REMOVE THROTTLE BODY ASSEMBLY


    A156180E01
  1. Remove the nut, 3 bolts, throttle body and gasket.



15. REMOVE NO. 1 VENTILATION HOSE


16. REMOVE PURGE VSV


    A162052
  1. Disconnect the purge line hose from the intake manifold.

  1. Remove the bolt and purge VSV.



17. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A156178
  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolt, VSV connector and VSV from the intake manifold.

  1. Disconnect the VSV connector.



18. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A160920
  1. Disconnect the fuel return hose from the pressure regulator.

    NOTICE:
    Put a cloth or equivalent under the pressure regulator.



    A160921
  1. Remove the 3 bolts and fuel return pipe from the delivery pipe and intake manifold.

    HINT:
    Move the fuel return pipe aside to secure more work space.



    A160927
  1. Remove the bolt, 2 union bolts, 4 gaskets and front fuel pipe.

  1. Disconnect the 8 injector connectors.

  1. Remove the 4 nuts holding the delivery pipes to the lower intake manifold.

  1. Remove the 2 delivery pipes.

    NOTICE:
    Be careful not to drop the injectors when removing the delivery pipes.