Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR (for Double Cab)

FRONT DOOR (for Double Cab) > DISASSEMBLY

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    B165648E02
  1. Using a screwdriver, detach the 4 claws and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT UPPER ARMREST BASE PANEL LH


    B166211
  1. Using a screwdriver, detach the 2 clips and front armrest upper base panel.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connectors.



4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B166212
  1. Remove the 3 screws and power window regulator master switch.



5. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH LH


    B168274E01
  1. Detach the 3 clips and remove the door lower frame bracket garnish.



6. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)


B171783
  1. Remove the 3 screws and speaker with bracket.



    B165754E01
  1. Detach the 3 claws and remove the speaker from the bracket.

    NOTICE:
    Do not touch the cone part of the speaker.



7. REMOVE COURTESY LIGHT ASSEMBLY


    B165655
  1. Detach the claw and remove the courtesy light from the door trim board.

  1. Disconnect the connector.



8. REMOVE FRONT DOOR ARMREST COVER LH


9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B166215E01
  1. Remove the 2 screws.

  1. Using a clip remover, remove the clip.

  1. Detach the 9 clips and remove the trim cover. Then disconnect the connector.



    B165654E01
  1. Disconnect the 2 cables from the inside handle.

  1. Remove the inside handle.



10. REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH


11. REMOVE SEAT MEMORY SWITCH (w/ Seat Memory Switch)


    B166227
  1. Remove the 2 screws and seat memory switch.



12. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Power Mirror Control System)


    B166706
  1. Disconnect the 2 ECU connectors.

  1. Remove the 2 screws and ECU.



13. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH


B166364E02
  1. w/ Power Mirror Control System:
    Disconnect the connector labeled A.

  1. Remove the 3 nuts and claw.

  1. Remove the outer rear view mirror.



14. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


B165746
  1. Disconnect the speaker connector.

  1. Remove the 4 screws and speaker.

    NOTICE:
    Do not touch the cone part of the speaker.



15. REMOVE FRONT NO. 1 DOOR TRIM BRACKET


    B165656
  1. Remove the 2 screws and bracket.



16. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    B166952
  1. Using a clip remover, detach the 2 clamps.



    B165658
  1. Remove the front door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.



17. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. for Driver Side:

    1. Temporarily install the power window regulator master switch.

  1. for Passenger Side:

    1. Temporarily install the power window regulator switch.

  1. Connect the cable to the negative (-) battery terminal.



    B166216
  1. Move the door glass until the bolts appear in the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.



    B166217
  1. Remove the door glass in the direction indicated by the arrows in the illustration.

    HINT:
    Remove the glass upward.

    NOTICE:
    Be careful not to damage the glass.

  1. for Driver Side:

    1. Remove the power window regulator master switch.

  1. for Passenger Side:

    1. Remove the power window regulator switch.

  1. Disconnect the cable from the negative battery (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    1. Some systems need to be initialized after the cable is reconnected (Click here).
    2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



18. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
  1. Disconnect the connector.



    B166218E02
  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and become damaged.

  1. Remove the 5 bolts and window regulator.

  1. Remove the window regulator through the service hole.

  1. Remove the temporary bolt from the front door window regulator.



19. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B165662
  1. Using a T25 "TORX" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.



20. REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH


    B166953
  1. Disconnect the connector.

  1. Remove the bolt and side airbag sensor.



21. REMOVE FRONT OUTER DOOR GLASS WEATHERSTRIP ASSEMBLY LH


B165859E01
  1. Put protective tape around the weatherstrip outer.

  1. Using a moulding remover, detach the claw and remove the weatherstrip.



22. REMOVE FRONT DOOR GLASS RUN LH


    B165689
  1. Remove the front door glass run.



23. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    B165664
  1. Remove the 2 bolts and front door rear lower frame.

    HINT:
    Remove the frame through the service hole.

    NOTICE:
    Be careful when removing the bolts as the frame may fall and become damaged.



24. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH


    B165663
  1. Remove the 2 bolts and front door front lower frame.

    HINT:
    Remove the frame through the service hole.

    NOTICE:
    Be careful when removing the bolts as the frame may fall and become damaged.



25. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    B165665E02
  1. Remove the hole plug.

  1. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.

  1. Remove the cylinder from the cover.



26. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    B165669
  1. Disconnect the connector.

  1. Using a T30 "TORX" wrench, remove the 3 screws and door lock.

    HINT:
    Remove the door lock through the service hole.

    NOTICE:
    Be careful when removing the bolts as the door lock may fall and become damaged.



27. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B165670E01
  1. Remove the front door lock remote control cable assembly.



28. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B165671
  1. Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.



    B165672E01
  1. Remove the front door inside locking cable.



29. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH


    B165666
  1. Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

    NOTICE:
    If the release plate is not pulled and held when removing the handle, the release plate will interfere with the handle and become damaged.



30. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
  1. Remove the front and rear outside handle pads.



    B165673
  1. Using a T30 "TORX" wrench, loosen the screw.

  1. Slide the outside handle frame to remove it.

    HINT:
    Remove the outside handle frame through the service hole.



31. REMOVE FRONT DOOR LOCK OPEN ROD LH
  1. Remove the lock open rod from the outside handle frame.



32. REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION


    B165680
  1. Using a clip remover, remove the 2 clips and stiffener cushion.



33. REMOVE FRONT DOOR PANEL PROTECTOR LH


    B166214
  1. Using a clip remover, detach the 8 clips and remove the door panel protector.

    HINT:
    If clips are damaged during removal, replace them.



34. REMOVE FRONT DOOR CHECK ASSEMBLY LH


    B165675
  1. Remove the bolt, 2 nuts and door check.

    HINT:
    Remove the door check through the service hole.

    NOTICE:
    Be careful when removing the bolts as the door check may fall and become damaged.



35. REMOVE FRONT DOOR WEATHERSTRIP LH


    B166219
  1. Using a clip remover, detach the 38 clips and remove the weatherstrip.

    HINT:
    If clips are damaged during removal, replace them.