Home › BODY ELECTRICAL › DOOR LOCK › REAR DOOR LOCK (for Double Cab)

REAR DOOR LOCK (for Double Cab) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    B166242
  1. Using a screwdriver, detach the 4 claws and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE REAR DOOR ARMREST UPPER BASE PANEL LH


    B166243
  1. Using a screwdriver, detach the 2 clips and rear upper door armrest base panel. Then disconnect the connector.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE REAR DOOR FRAME GARNISH LH


    B167090
  1. Detach the 4 clips and remove the rear door frame garnish.



5. REMOVE COURTESY LIGHT ASSEMBLY


  1. for Double Cab:



      E142765
    1. Using a screwdriver, detach the claw.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the courtesy light and then disconnect the connector.



  1. for CrewMax:



      E142764
    1. Using a screwdriver, detach the claw.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the courtesy light and then disconnect the connector.



6. REMOVE REAR DOOR ARMREST COVER LH


7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B166244E01
  1. Remove the 2 screws.

  1. Using a clip remover, remove the clip.

  1. Detach the 9 clips and remove the trim cover. Then disconnect the connector.



    B165654E01
  1. Disconnect the 2 cables from the inside handle.



8. REMOVE REAR NO. 2 DOOR TRIM BRACKET


    B166245
  1. Remove the 2 screws and bracket.



9. REMOVE REAR DOOR SERVICE HOLE COVER LH


    B166246E01
  1. Disconnect the connector and 2 clamps.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door.



10. REMOVE REAR DOOR GLASS RUN LH


    B166248
  1. Remove the rear door glass run.



11. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY LH


    B166247
  1. Remove the 4 bolts and rear door rear lower window frame.

    HINT:
    Remove the frame through the service hole.

    NOTICE:
    Be careful when removing the bolts as the frame may fall and become damaged.



12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


B166250
  1. Remove the rear door glass from the rear door window regulator as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



13. REMOVE REAR DOOR LOCK ASSEMBLY LH


    B166253
  1. Disconnect the connector.

  1. Using a T30 "TORX" wrench, remove the 3 screws and door lock.

    HINT:
    Remove the door lock through the service hole.

    NOTICE:
    Be careful when removing the bolts as the door lock may fall and become damaged.



14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B165670E01
  1. Remove the rear door lock remote control cable.



15. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B167681
  1. Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.



    B167682E01
  1. Remove the rear door inside locking cable.