Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION RECEIVER (for Floor Shift Type)

NAVIGATION RECEIVER (for Floor Shift Type) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE FRONT DOOR SCUFF PLATE LH
  1. for Double Cab:
    Remove the front door scuff plate LH .

  1. for CrewMax:
    Remove the front door scuff plate LH .



3. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



4. REMOVE INSTRUMENT SIDE PANEL LH


    B160581
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B168286
  1. Remove the hood lock control lever.

  1. Remove the 2 bolts.

  1. Detach the 4 clips and claw.



    B163883
  1. for Automatic Air Conditioning System:
    Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



6. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B161741
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



7. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Detach the 12 clips and remove the console panel.



8. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161744
  1. Using a moulding remover, detach the 7 clips and remove the end panel.

  1. except Regular Cab:
    Disconnect the connector.



9. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY


    B161744
  1. Using a moulding remover, detach the 7 clips and remove the end panel.

  1. except Regular Cab:
    Disconnect the connector.



10. REMOVE CONSOLE BOX CARPET


11. REMOVE REAR CONSOLE BOX ASSEMBLY


    B161745
  1. Remove the 2 screws.

  1. Remove the 4 bolts and rear console box.



12. REMOVE FRONT CONSOLE BOX


    B161746
  1. Remove the 2 clips.

  1. Remove the 6 screws and front console box.



13. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B164474
  1. Disconnect the connector and clamp.

  1. Detach the 12 clips and remove the finish panel.



14. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B161747
  1. Detach the 4 clips.

  1. Remove the finish panel and then disconnect the connectors.



15. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning System)


    B160589
  1. Detach the 4 clips.

  1. Remove the panel and then disconnect the connectors.



16. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air Conditioning System)


    B160588
  1. Detach the 4 clips.

  1. Remove the panel and then disconnect the connectors.



17. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET


B164792
  1. Remove the 4 bolts.



    B164793
  1. Pull the navigation receiver as shown in the illustration to detach the 3 clips on the backside of the navigation receiver.

  1. Disconnect the connectors and remove the navigation receiver.



18. REMOVE NO. 1 RADIO BRACKET


B164794
  1. Remove the 4 bolts and bracket.



19. REMOVE NO. 2 RADIO BRACKET


B164795
  1. Remove the 4 bolts and bracket.