Home › ENGINE ยท 3UR-FBE › LUBRICATION › ENGINE OIL COOLER

ENGINE OIL COOLER > INSTALLATION

for Preparation Click here



1. INSTALL OIL COOLER SPACER


    A162474E01
  1. Apply a light coat of engine oil to a new gasket.

  1. Install the gasket to the oil cooler spacer.



    A162472
  1. Install the oil cooler spacer to the oil filter bracket with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



2. INSTALL OIL COOLER ASSEMBLY


    A162475
  1. Apply a light coat of engine oil to 2 new O-rings.

  1. Install the 2 O-rings to the oil cooler.



    A162471
  1. Install the oil cooler with the 5 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



3. INSTALL OIL FILTER BRACKET


    A162470
  1. Apply a light coat of engine oil to 2 new O-rings.

  1. Install the 2 O-rings to the timing chain cover.



    A162469
  1. Install the oil filter bracket with the 2 nuts and 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



4. INSTALL NO. 1 OIL COOLER BRACKET


    A163672
  1. Connect the ground wire to the cylinder block.

  1. Install the oil cooler bracket with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



5. INSTALL NO. 2 WATER BY-PASS PIPE


    A162468
  1. Connect the 4 hoses.

  1. Install the water by-pass hose with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. CONNECT COOLER COMPRESSOR ASSEMBLY


    A163332E01
  1. Install the cooler compressor with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 2 bolts and 2 nuts.

    NOTICE:
    Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



7. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY


    A186675E01
  1. Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    A162467
  1. Install the oil pressure sender gauge.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation.



    A163657
  1. Connect the sender gauge connector.



8. INSTALL OIL FILTER ELEMENT
  1. Install the oil filter element (Click here).



9. INSTALL FAN AND GENERATOR V BELT
  1. Install the fan and generator V belt (Click here).



10. ADD ENGINE OIL
  1. Add fresh oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    0W-20
    5W-20
    (0W-20 is best choice for fuel economy and good starting in cold weather.)

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    7.0 liters (7.4 US qts, 6.2 Imp. qts)
    Drain and refill without oil filter change
    6.6 liters (7.0 US qts, 5.8 Imp. qts)
    Dry fill
    8.4 liters (8.9 US qts, 7.4 Imp. qts)

  1. Install the oil filler cap.



11. ADD ENGINE COOLANT
  1. Add engine coolant.
    Standard capacity: 
    Item
    Specified Condition
    w/ Trailer Towing System
    13.0 liters (13.7 US qts, 11.4 Imp. qts)
    w/o Trailer Towing System
    12.1 liters (12.8 US qts, 10.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



13. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



14. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.



15. INSPECT FOR COOLANT LEAK


A161766

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.