Home › ENGINE · 3UR-FBE › EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After the ignition switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.
  2. When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A191562E01

  1. Tighten the radiator drain cock plug by hand.



4. REMOVE V-BANK COVER SUB-ASSEMBLY


    A165576E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



5. REMOVE AIR CLEANER HOSE ASSEMBLY


    A162102E01
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



6. REMOVE AIR CLEANER ASSEMBLY


    A162105E01
  1. Remove the air cleaner cap.

    1. Disconnect the MAF meter connector.

    2. Using a clip remover, detach the wire harness clamp.

    3. Unfasten the 4 hook clamps and then remove the air cleaner cap.

  1. Remove the air cleaner element.



    A156197E01
  1. Remove the 2 bolts and air cleaner case.



7. DISCONNECT INLET RADIATOR HOSE


8. DISCONNECT OUTLET RADIATOR HOSE


9. REMOVE FAN AND GENERATOR V-BELT


    A163770E01
  1. While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar of φ 5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.

    HINT:
    The pulley bolt for the belt tensioner has a left-hand thread.

  1. Remove the V belt.



10. REMOVE FAN SHROUD


    A151842
  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt.

  1. Disconnect the reservoir hose from the upper radiator tank.



    A161784
  1. w/ Trailer Towing System:
    Detach the claw to open the No. 1 flexible hose clamp.



    A151821
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the fan bracket.



11. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 6 clips and fender apron seal.



12. REMOVE FRONT FENDER APRON SEAL REAR RH
  1. Remove the 5 clips and fender apron seal.



13. REMOVE FRONT FENDER APRON SEAL LH
  1. Remove the 6 clips and fender apron seal.



14. REMOVE FRONT FENDER APRON SEAL REAR LH
  1. Remove the 5 clips and fender apron seal.



15. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.



    A164432
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



16. DISCONNECT VANE PUMP ASSEMBLY


    A164433
  1. Disconnect the 2 clamps and power steering oil pressure switch connector.



    A163289
  1. Remove the 2 bolts and disconnect the vane pump.



17. REMOVE GENERATOR ASSEMBLY


    A163292
  1. Disconnect the generator connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.



    A163290
  1. Remove the bolt and disconnect the wire harness bracket from the generator.



    A163293
  1. Remove the 2 bolts, 2 nuts and generator.



18. DISCONNECT COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



19. REMOVE PROPELLER SHAFT HEAT INSULATOR


    A158903
  1. Remove the 2 bolts and heat insulator.



20. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


C158457E01
  1. for Front Differential Side:

    1. Place matchmarks on the differential and propeller shaft flange.

    2. Remove the 4 nuts, 4 washers and disconnect the propeller shaft from the differential.

      NOTICE:
      Use a rope to suspend the front edge of the propeller shaft.



    C158456E02
  1. for Transfer Side:

    1. Place matchmarks on the transfer and propeller shaft flanges.

    2. Remove the 4 nuts and 4 washers.

  1. Remove the propeller shaft from the transfer flange.



21. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for Regular Cab Standard Deck)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Remove the 2 bolts, 5 nuts, No. 2 exhaust pipe and 2 gaskets.



22. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (except Regular Cab Standard Deck)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Remove the 2 bolts and 3 nuts.

  1. Disconnect the front No. 2 exhaust pipe from the exhaust pipe support to remove it.

  1. Remove the 2 gaskets.



23. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector and 2 clamps.

  1. Remove the 2 bolts from the center exhaust pipe.

  1. Remove the 3 nuts, front exhaust pipe and 2 gaskets.



24. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C155150E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and steering intermediate shaft.

  1. Remove the bolt and disconnect the No. 2 steering intermediate shaft from the steering intermediate shaft.



    C155151E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and the power steering gear.

  1. Remove the bolt and disconnect the No. 2 steering intermediate shaft from the power steering gear.



25. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A162114
  1. Remove the 3 bolts and heat insulator.



26. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A162115
  1. Remove the 10 nuts, exhaust manifold and 2 gaskets.



27. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A162752
  1. Remove the 3 bolts and heat insulator.



28. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A162754
  1. Remove the 10 nuts, exhaust manifold and 2 gaskets.