DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2120 | VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). |
|
| P2122 | VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic). |
|
| P2123 | VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic). |
|
| P2125 | VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). |
|
| P2127 | VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic). |
|
| P2128 | Conditions (a) and (b) are met for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or higher. (b) VPA is between 0.4 V and 3.45 V. |
|
| P2138 | Condition (a) or (b) is met for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 is 0.02 V or less. (b) VPA is 0.4 V or less and VPA2 is 1.2 V or less. |
|
| Trouble Area | Accel Sensor Out No.1 When Accelerator Pedal Released | Accel Sensor Out No.2 When Accelerator Pedal Released | Accel Sensor Out No.1 When Accelerator Pedal Depressed | Accel Sensor Out No.2 When Accelerator Pedal Depressed |
| VCP circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or short to ground in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.75 V |
| Open or short to ground in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.75 V |
| Related DTCs | P2120: Accelerator pedal position sensor 1 range check (fluctuating) P2122: Accelerator pedal position sensor 1 range check (low voltage) P2123: Accelerator pedal position sensor 1 range check (high voltage) P2125: Accelerator pedal position sensor 2 range check (fluctuating) P2127: Accelerator pedal position sensor 2 range check (low voltage) P2128: Accelerator pedal position sensor 2 range check (high voltage) P2138: Accelerator pedal position sensor range check (correlation) |
| Required Sensors/Components (Main) | Accelerator pedal position sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P2120, P2122, P2125 and P2127 2.0 seconds: P2123, P2128 and P2138 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Either of following conditions 1 or 2 met: | - |
| 1. Time after ignition switch off to ON | 0.012 seconds or more |
| 2. Throttle actuator power | ON |
| Either of following conditions 1 or 2 met: | - |
| 1. All of following conditions met: | (a) and (b) |
| (a) VPA voltage | 0.4 V or less |
| (b) VPA2 voltage - Learned VPA2 accelerator off position voltage | 0.04 V or more |
| 2. VPA voltage | 4.8 V or higher |
| All of following conditions met: | (a) and (b) |
| (a) VPA voltage | 0.4 V or less |
| (b) VPA2 voltage - Learned VPA2 accelerator off position voltage | 0.04 V or more |
| VPA voltage | 4.8 V or higher |
| Either of following conditions 1 or 2 met: | - |
| 1. All of following conditions met: | (a) and (b) |
| (a) VPA2 voltage | 1.2 V or less |
| (b) VPA voltage - Learned VPA accelerator off position voltage | 0.04 V or higher |
| 2. VPA2 voltage when VPA voltage 0.4 to 3.45 V | 4.8 V or higher |
| All of following conditions met: | (a) or (b) |
| (a) VPA2 voltage | 1.2 V or less |
| (b) VPA voltage - Learned VPA accelerator off position voltage | 0.04 V or higher |
| VPA2 voltage when VPA voltage 0.4 to 3.45 V | 4.8 V or higher |
| Either of following conditions A or B met: | - |
| Condition A | - |
| Difference between VPA and VPA2 voltages | 0.02 V or less |
| Condition B | - |
| VPA voltage | 0.4 V or less |
| VPA2 voltage | 1.2 V or less |
| VPA voltage | 0.4 to 4.8 V |
| VPA2 voltage | 1.2 to 4.8 V |
| Difference between VPA and VPA2 voltages | More than 0.02 V |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (ACCEL SENSOR OUT NO.1 AND ACCEL SENSOR OUT NO.2) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.
Read the value displayed on the Techstream.
| Accelerator Pedal Operation | Accel Sensor Out No.1 | Accel Sensor Out No.2 | Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V | More than 0.02 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 4.7 V |
| *a | Depressed |
| *b | Released |
|
| ||||
|
| ||||
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ROD ASSEMBLY - ECM) |
Disconnect the accelerator pedal rod assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A14-6 (VPA) - A24-55 (VPA) | Always | Below 1 Ω |
| A14-5 (EPA) - A24-58 (EPA) | Always | Below 1 Ω |
| A14-4 (VCPA) - A24-57 (VCPA) | Always | Below 1 Ω |
| A14-3 (VPA2) - A24-56 (VPA2) | Always | Below 1 Ω |
| A14-2 (EPA2) - A24-60 (EPA2) | Always | Below 1 Ω |
| A14-1 (VCP2) - A24-59 (VCP2) | Always | Below 1 Ω |
| A14-6 (VPA) or A24-55 (VPA) - Body ground | Always | 10 kΩ or higher |
| A14-5 (EPA) or A24-58 (EPA) - Body ground | Always | 10 kΩ or higher |
| A14-4 (VCPA) or A24-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A14-3 (VPA2) or A24-56 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A14-2 (EPA2) or A24-60 (EPA2) - Body ground | Always | 10 kΩ or higher |
| A14-1 (VCP2) or A24-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the accelerator pedal rod assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A14-4 (VCPA) - A14-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| A14-1 (VCP2) - A14-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Accelerator Pedal Rod Assembly) |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 is output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||