Home › ENGINE ยท 3UR-FBE › FUEL › FUEL INJECTOR

FUEL INJECTOR > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.



    A194647
  1. Disconnect the 2 fuel pump ECU connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the 2 fuel pump ECU connectors.



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


4. REMOVE V-BANK COVER


    A165576E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



5. REMOVE AIR CLEANER HOSE ASSEMBLY


    A162102E01
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



6. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    A161418
  1. Disconnect the No. 2 fuel tube from the fuel pressure regulator (for quick type) (Click here).



7. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A256329
  1. Disconnect the fuel tube from the fuel delivery pipe RH (for quick type) (Click here).



    A161415
  1. Disconnect the fuel tube from the fuel delivery pipe LH (for quick type) (Click here).



8. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A161416
  1. Disconnect the No. 1 fuel pipe from the fuel delivery pipe LH (for quick type) (Click here).



9. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH


    A198623
  1. Disconnect the ventilation hose and No. 6 wire harness connector.

  1. Remove the No. 3 engine cover.



    A256377
  1. Remove the 2 bolts and fuel delivery pipe RH.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head RH.



10. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH
  1. Disconnect the No. 7 wire harness connector.

  1. Remove the No. 1 engine cover sub-assembly.



    A256378
  1. Remove the 2 bolts and fuel delivery pipe LH.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head LH.



11. REMOVE FUEL INJECTOR ASSEMBLY


    A161427
  1. Remove the fuel injector from the fuel delivery pipe, and then disconnect the injector connector.

    NOTICE:
    A149189E01
    For reinstallation, attach a tag or label to the injector shaft.



    A149190E01
  1. Remove the O-ring from the fuel injector.



    A256379
  1. Detach the 3 clamps and then remove the No. 6 wire harness from the delivery pipe RH.



    A256380
  1. Detach the 3 clamps and then remove the No. 7 wire harness from the delivery pipe LH.