Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0347    Camshaft Position Sensor "A" Circuit Low Input (Bank 2)

DTC    P0348    Camshaft Position Sensor "A" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, VV2 signal) consists of a magnet and MRE (Magnetoresistive Element).
The camshaft timing gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends the camshaft angle data to the ECM.
The crankshaft angle sensor rotor has 34 teeth. The pickup coil generates 34 signals for each crankshaft revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No.
DTC Detection Condition
Trouble Area
P0340
Either condition is met:
  1. No VVT sensor signal is sent to the ECM while cranking (2 trip detection logic).
  2. There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in VVT sensor (for intake side of bank 1) circuit
  2. VVT sensor (for intake side of bank 1)
  3. Camshaft timing gear assembly
  4. Timing chain for intake camshaft has jumped tooth
  5. ECM
P0345
There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in VVT sensor (for intake side of bank 2) circuit
  2. VVT sensor (for intake side of bank 2)
  3. Camshaft timing gear assembly
  4. Timing chain for intake camshaft has jumped tooth
  5. ECM
P0342
P0347
Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for intake side) circuit
  2. VVT sensor (for intake side)
  3. Camshaft timing gear assembly
  4. Timing chain for intake camshaft has jumped tooth
  5. ECM
P0343
P0348
Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for intake side) circuit
  2. VVT sensor (for intake side)
  3. Camshaft timing gear assembly
  4. Timing chain for intake camshaft has jumped tooth
  5. ECM

  1. A199235E01
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveforms are as shown.
    2. VV1 and VV2 are the VVT sensor signals, and NE is the crankshaft position sensor signal.

    Item
    Content
    Terminal
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Setting
    5 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the VVT sensor.

MONITOR STRATEGY


Related DTCs
P0340: VVT sensor (Bank 1) verify pulse input
P0340: Camshaft position/Crankshaft position misalignment (Bank 1)
P0342: VVT sensor (Bank 1) range check (low voltage)
P0343: VVT sensor (Bank 1) range check (high voltage)
P0345: VVT sensor (Bank 2) verify pulse input
P0347: VVT sensor (Bank 2) range check (low voltage)
P0348: VVT sensor (Bank 2) range check (high voltage)
Required Sensors/Components (Main)
VVT sensor (for intake side)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
4 seconds: P0340 (VVT sensor (Bank 1) verify pulse input), P0342, P0343, P0347 and P0348
5 seconds: Others
MIL Operation
2 driving cycles: P0340 (VVT sensor (Bank 1) verify pulse input)
Immediate: Others
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
None

P0340 VVT Sensor Verify Pulse Input 
Starter
ON
Minimum battery voltage while starter ON
Less than 11 V

P0340 Camshaft Position/Crankshaft Position Misalignment 
Engine speed
600 rpm or more
Starter
OFF
VVT system mis-alignment
Not detected
VVT sensor range check fail (P0342, P0343)
Not detected
VVT sensor voltage
0.3 V or more, and 4.7 V or less

P0342, P0343 VVT Sensor Range Check (Low Voltage, High Voltage) 
Starter
OFF
Ignition switch
ON
Time after ignition switch off to ON
2 seconds or more
Battery voltage
8 V or more
VVT sensor pulse input fail (P0340)
Not detected

P0347, P0348 VVT Sensor Range Check (Low Voltage, High Voltage) 
Starter
OFF
Ignition switch
ON
Time after ignition switch off to ON
2 seconds or more
Battery voltage
8 V or more
VVT sensor pulse input fail (P0340, P0345)
Not detected

P0345 VVT Sensor Verify Pulse Input 
Engine speed
600 rpm or more
Starter
OFF
VVT sensor voltage
0.3 V or more, and 4.7 V or less
Battery voltage
8 V or more
Ignition switch
ON
Time after ignition switch off to ON
0.5 seconds or more
VVT sensor range check fail (P0342, P0343, P0347, P0348)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


P0340, P0345 VVT Sensor Verify Pulse Input 
VVT sensor signal
No signal

P0340 Camshaft Position/Crankshaft Position Misalignment 
Either of the following conditions is met
1 or 2
1. Camshaft position and crankshaft position alignment
Misaligned
2. VVT sensor signal
No signal

P0342, P0347 VVT Sensor Range Check (Low Voltage) 
VVT sensor voltage
Less than 0.3 V

P0343, P0348 VVT Sensor Range Check (High Voltage) 
VVT sensor voltage
More than 4.7 V

COMPONENT OPERATING RANGE


VVT sensor voltage
0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A160377E09


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR INTAKE SIDE))


    A208648E23
  1. Disconnect the VVT sensor (for intake side) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D79-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V
    D78-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V

    Text in Illustration 
    *A
    for Bank 1
    *B
    for Bank 2
    *a
    Front view of wire harness connector
    (to VVT Sensor (for Intake Side))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM)
  1. Disconnect the VVT sensor (for intake side) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D79-1 (VVR+) - D74-90 (VV1+)
    Always
    Below 1 Ω
    D79-2 (VVR-) - D74-89 (VV1-)
    Always
    Below 1 Ω
    D78-1 (VVL+) - D74-87 (VV2+)
    Always
    Below 1 Ω
    D78-2 (VVL-) - D74-88 (VV2-)
    Always
    Below 1 Ω
    D79-1 (VVR+) or D74-90 (VV1+) - Body ground
    Always
    10 kΩ or higher
    D79-2 (VVR-) or D74-89 (VV1-) - Body ground
    Always
    10 kΩ or higher
    D78-1 (VVL+) or D74-87 (VV2+) - Body ground
    Always
    10 kΩ or higher
    D78-2 (VVL-) or D74-88 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE SIDE))


    BR03795E17
  1. Check the VVT sensor (for intake side) installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


    A103826E11
  1. Remove the cylinder head cover RH and LH.

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark

  1. Reinstall the cylinder head cover RH and LH.



NG
ADJUST VALVE TIMING
OK


6.REPLACE VVT SENSOR (FOR INTAKE SIDE)
  1. Replace the VVT sensor (for intake side) (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Refer to the confirmation driving pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0340, P0342, P0343, P0345, P0347 or P0348 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END