DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |
DTC P2197 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1) |
DTC P2198 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1) |

| DTC Code | DTC Detection Condition | Trouble Area |
| P2195 P2197 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor voltage is higher than 3.8 V. (b) Heated oxygen sensor voltage is 0.21 V or higher. |
|
| While fuel-cut operation performed (during vehicle deceleration), A/F sensor current 2.2 mA or more for 3 seconds (2 trip detection logic) |
| |
| P2196 P2198 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor voltage is below 2.8 V. (b) Heated oxygen sensor voltage is below 0.59 V. |
|
| While fuel-cut operation performed (during vehicle deceleration), A/F sensor current less than 0.7 mA for 3 seconds (2 trip detection logic) |
|

| Related DTCs | P2195: A/F sensor signal stuck lean (Bank 1) P2196: A/F sensor signal stuck rich (Bank 1) P2197: A/F sensor signal stuck lean (Bank 2) P2198: A/F sensor signal stuck rich (Bank 2) |
| Required Sensors/Components (Main) | A/F sensor |
| Required Sensors/Components (Related) | HO2 sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds: Sensor voltage detection monitor 3 seconds: Sensor current detection monitor |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016, P0018 (VVT System - Misalignment) P0017, P0019 (Exhaust VVT System - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P1340 (Camshaft position sensor) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control) P0451, P0452, P0453 (EVAP system) P2440 - P2447 (Secondary air injection system) P0500, P0722 (Vehicle Speed Sensor) P0505 (IAC valve) |
| Time after engine start | 30 seconds or more |
| A/F sensor status | Activated |
| Fuel system status | Closed-loop |
| Battery voltage | 11 V or more |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| A/F sensor status | Activated |
| Continuous time of fuel cut | 3 to 10 seconds |
| ECT | 75°C (167°F) or more |
| Rear heated oxygen sensor voltage | 0.21 V or higher |
| Air fuel ratio sensor voltage | Higher than 3.8 V |
| Rear heated oxygen sensor voltage | Below 0.59 V |
| Air fuel ratio sensor voltage | Below 2.8 V |
| Air fuel ratio sensor current | 2.2 mA or more |
| Air fuel ratio sensor current | Less than 0.7 mA |


| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P2195, P2196, P2197 or P2198 is output | A |
| "DTC P2195, P2196, P2197 or P2198" and "DTC P0136, P0137, P0138, P0156, P0157 or P0158" are output | A |
| DTC P2195, P2196, P2197 or P2198 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | |
| 3.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | B |
|
| ||||
| A | ||
| ||
| 4.READ VALUE USING TECHSTREAM (TEST VALUE OF A/F SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Drive the vehicle in accordance with the drive pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Current.
Check that the status of O2 Sensor is Complete. If the status is still Incomplete, drive the vehicle according to the driving pattern again.
Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RANGE B1S1 or RANGE B2S1.
Check the test value of the air fuel ratio sensor output current during fuel-cut.
| Result | Proceed to |
| Within normal range (0.7 mA or higher, and below 2.2 mA) | A |
| Outside normal range (below 0.7 mA, or 2.2 mA or higher) | B |
|
| ||||
| A | |
| 5.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio) | +12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 or O2S B2S2 (Heated oxygen) | +12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 or AFS Voltage B2S1 | Status of O2S B1S2 or O2S B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Lean/Rich | Lean/Rich | Normal | B |
|
| ||||
| A | |
| 6.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leaks .
|
| ||||
| OK | |
| 7.CHECK EXHAUST GAS LEAK |
Check for exhaust gas leaks from the exhaust manifold assembly and exhaust pipes.
|
| ||||
| OK | |
| 8.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 9.INSPECT FUEL INJECTOR ASSEMBLY |
Check the fuel injector (whether fuel volume is high or low, and whether injector pattern is poor) .
|
| ||||
| OK | |
| 10.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 11.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 12.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTC (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | B |
|
| ||||
| A | ||
| ||
| 16.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||