Home › ENGINE ยท 1UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

DTC    P2197    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)

DTC    P2198    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the A/F sensor is a current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.

A178930E03


DTC No.
DTC Detection Condition
Trouble Area
P2195
P2197
Conditions (a) and (b) continue for 5 seconds or more
(2 trip detection logic):
(a) A/F sensor voltage more than 3.8 V
(b) Heated oxygen (HO2) sensor voltage is 0.21 V or higher
  1. Open or short in A/F sensor (for Sensor 1) circuit
  2. A/F sensor (for Sensor 1)
  3. A/F sensor heater (for Sensor 1)
  4. Integration relay
  5. A/F sensor heater and integration relay circuits
  6. Air induction system
  7. Fuel pressure
  8. Injector
  9. EGR valve
  10. ECM
While fuel-cut operation performed (during vehicle deceleration), A/F sensor current 3.6 mA or more for 3 seconds (2 trip detection logic)
  1. A/F sensor
  2. EGR valve
  3. ECM
P2196
P2198
Conditions (a) and (b) continue for 5 seconds or more
(2 trip detection logic):
(a) A/F sensor voltage less than 2.8 V
(b) HO2 sensor voltage is below 0.59 V
  1. Open or short in A/F sensor (for Sensor 1) circuit
  2. A/F sensor (for Sensor 1)
  3. A/F sensor heater (for Sensor 1)
  4. Integration relay
  5. A/F sensor heater and integration relay circuits
  6. Air induction system
  7. Fuel pressure
  8. Injector
  9. EGR valve
  10. ECM
While fuel-cut operation performed (during vehicle deceleration), A/F sensor current less than 1.4 mA for 3 seconds (2 trip detection logic)
  1. A/F sensor
  2. EGR valve
  3. ECM

HINT:
  1. DTCs P2195 and P2196 indicate malfunctions related to the bank 1 A/F sensor circuit.
  2. DTCs P2197 and P2198 indicate malfunctions related to the bank 2 A/F sensor circuit.
  3. When any of these DTCs is stored, check the A/F sensor output voltage by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Voltage B1S1 or AFS Voltage B2S1.
  4. Short-term fuel trim values can also be read using the Techstream.
  5. The ECM regulates the voltages at the A1A+ and A1A- or A2A+ and A2A- terminals of the ECM to a constant level. Therefore, the A/F sensor output voltage cannot be confirmed without using the Techstream.
  6. If the A/F sensor is malfunctioning, the ECM stores DTC P2195, P2196, P2197 or P2198.


MONITOR DESCRIPTION

  1. Sensor voltage detection monitor
    Under the air-fuel ratio feedback control, if the A/F sensor output voltage indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the A/F sensor. The ECM illuminates the MIL and stores a DTC.
    Example:
    If the A/F sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds, despite the rear HO2 sensor output voltage being less than 0.59 V, the ECM stores DTC P2196 or P2198. Alternatively, if the A/F sensor output voltage is more than 3.8 V (very lean condition) for 5 seconds despite the rear HO2 sensor output voltage being 0.21 V or more, DTC P2195 or P2197 is stored.
  1. Sensor current detection monitor
    A rich air-fuel mixture causes a low A/F sensor current, and a lean air-fuel mixture causes a high A/F sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the A/F sensor current during fuel-cut and detects any abnormal current values.
    If the A/F sensor output is 3.6 mA or more for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the A/F sensor and stores DTC P2195 or P2197 (high-side stuck). If the A/F sensor output is less than 1.4 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 or P2198 (low-side stuck).

A107165E29


MONITOR STRATEGY


Related DTCs
P2195: A/F sensor signal stuck lean (Bank 1)
P2196: A/F sensor signal stuck rich (Bank 1)
P2197: A/F sensor signal stuck lean (Bank 2)
P2198: A/F sensor signal stuck rich (Bank 2)
Required Sensors/Components (Main)
A/F sensor
Required Sensors/Components (Related)
HO2 sensor
Frequency of Operation
Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor
Duration
5 seconds: Sensor voltage detection monitor
3 seconds: Sensor current detection monitor
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0401 (EGR system)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control)
P0451, P0452, P0453 (EVAP system)
P0500, P0722 (Vehicle speed sensor)
P0505 (IAC valve)
P1340 (Camshaft position sensor)
P2440 - P2447 (Secondary air injection system)

Sensor Voltage Detection Monitor 
Time after engine start
30 seconds or more
A/F sensor status
Activated
Fuel system status
Closed-loop

Sensor Current Detection Monitor 
Battery voltage
11 V or more
Atmospheric pressure
76 kPa (570 mmHg) or more
A/F sensor status
Activated
Continuous time of fuel cut
3 to 10 seconds
ECT
75°C (167°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Sensor Voltage Detection Monitor (Lean Side Malfunction P2195 and P2197) 
Rear HO2S voltage
0.21 V or higher
A/F sensor voltage
More than 3.8 V

Sensor Voltage Detection Monitor (Rich Side Malfunction P2196 and P2198) 
Rear HO2S voltage
Below 0.59 V
A/F sensor voltage
Below 2.8 V

Sensor Current Detection Monitor (High Side Malfunction P2195 and P2197) 
A/F sensor current
3.6 mA or more

Sensor Current Detection Monitor (Rich Side Malfunction P2196 and P2198) 
A/F sensor current
Less than 1.4 mA

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.

A199318E01


A107163E78

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher [A].
  8. On the Techstream, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.
  9. Drive the vehicle at between 60 and 120 km/h (38 and 75 mph) for at least 10 minutes [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Shift the transmission to 2nd gear [C].
  11. Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal is fully released.
    2. Engine speed is 2500 rpm or more (fuel injection returns at 1000 rpm).

  13. Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
  14. Repeat steps [C] through [E] above at least 3 times in one driving cycle.
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  18. Input the DTC: P2195, P2196, P2197 or P2198.
  19. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.

  20. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A164734E01


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  5. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  6. Sensor 1 refers to the sensor closest to the engine assembly.
  7. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2195, P2196, P2197 or P2198 is output
    A
    "P2195, P2196, P2197 or P2198" and "P0136, P0137, P0138, P0156, P0157 or P0158" are output
    A
    P2195, P2196, P2197 or P2198 and other DTCs are output
    B

HINT:
If any DTCs relating to the A/F sensor (DTCs for the A/F sensor heater or A/F sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
Go to step 4
YES


3.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195, P2196, P2197 or P2198.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL
    (DTC is not output)
    A
    ABNORMAL
    (DTC P2195, P2196, P2197 or P2198 is output)
    B



NG
Go to step 4
A

DTC CAUSED BY RUNNING OUT OF FUEL 

4.READ VALUE USING TECHSTREAM (TEST VALUE OF A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle in accordance with the drive pattern described in the CONFIRMATION DRIVING PATTERN.

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor.

  1. Check that the status of O2 Sensor is Complete. If the status is still Incomplete, drive the vehicle according to the driving pattern again.

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details / RANGE B1S1 or RANGE B2S1.

  1. Check the test value of the A/F sensor output current during fuel-cut.
    Result 
    Test Value
    Proceed to
    Within normal range (1.4 mA or more, and less than 3.6 mA)
    A
    Outside normal range (Less than 1.4 mA, or 3.6 mA or more)
    B



B
Go to step 16
A


5.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the A/F sensor at an engine speed of 2500 rpm for 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Monitor the output Voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. Change the fuel injection volume within the range of -12.5% to +12.5%.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


Standard Voltage:

Techstream Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12.5%
Rich
Below 3.1 V
-12.5%
Lean
Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5%
Rich
Higher than 0.55 V
-12.5%
Lean
Below 0.4 V


Result 
Status of AFS Voltage B1S1 or AFS Voltage B2S1
Status of O2S B1S2 or O2S B2S2
Air Fuel Ratio Condition and Air fuel Ratio Sensor Condition
Proceed to
Lean
Lean
Actual air fuel ratio lean
A
Rich
Rich
Actual air fuel ratio rich
A
Lean
Lean/Rich
Air fuel ratio sensor malfunction
B
Rich
Lean/Rich
Air fuel ratio sensor malfunction
B
Lean/Rich
Lean/Rich
Normal
B
Lean: During the Control the injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.
Rich: During the Control the injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.
Lean/Rich: During the Control the injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.


B
Go to step 16
A


6.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks .

    OK:
    No leaks in air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


7.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leak.

    OK:
    No gas leak



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


8.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 18
OK


9.INSPECT FUEL INJECTOR
  1. Check the fuel injector (whether fuel volume is high or low, and whether injector pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR (Click here)
OK


10.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


11.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195, P2196, P2197 or P2198.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    ABNORMAL
    (DTC P2195, P2196, P2197 or P2198 is output)
    A
    NORMAL
    (DTC is not output)
    B



B
END
A


12.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    1. When performing the Active Test, make sure the shift lever is in P or N.
    2. The A/C switch and all accessory switches should be off.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.

    OK:
    MAP and idling condition change in response to EGR step position as follows.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stall
    MAP
    (Data List)
    20 to 40 kPa (150 to 300 mmHg)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed



OK
Go to step 14

NG
Go to step 13

13.INSPECT EGR VALVE
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.



NG
REPLACE EGR VALVE (Click here)
OK


14.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195, P2196, P2197 or P2198.

  1. Check the DTC judgment result.

    Result 
    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit


NEXT

END 

16.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


17.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195, P2196, P2197 or P2198.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL
    (DTC is not output)
    A
    ABNORMAL
    (DTC P2195, P2196, P2197 or P2198 is output)
    B



B
REPLACE ECM (Click here)
A

END 

18.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)