Home › ENGINE · 1GR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSPECTION

for Preparation Click here



1. INSPECT FUEL INJECTOR ASSEMBLY
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    11.6 to 12.4 Ω

    If the result is not as specified, replace the injector assembly.



2. INSPECT INJECTION VOLUME AND LEAKAGE


    A273848E01
  1. Check the injector injection.

    CAUTION:
    1. This test involves high-pressure fuel and electricity.
    2. Take every precaution regarding the safe handling of both the fuel and electrical parts.
    3. Perform this test in a safe area and avoid any sparks or flame.
    4. Do not smoke.


    1. Assemble SST as shown in the illustration.

      SST
      09268-31014   (09268-41091, 09268-41120, 09268-41141, 09268-41410, 09268-41500, 09268-41700, 95336-08070)
      Text in Illustration 
      *1
      Fuel Pressure Regulator
      *2
      SST (Union)
      *3
      SST (Hose Band)
      *4
      SST (Fuel Tube Connector)
      *5
      SST (Hose)
      *6
      SST (Adapter)
      *7
      SST (Clamp)
      *8
      Fuel Injector
      *9
      Fuel Pipe
      *10
      SST (T-Joint)

    2. Discharge the fuel system pressure (Click here).

    3. Disconnect the fuel inlet hose (fuel tube connector) from the fuel pipe.

    4. Remove the bolt and disconnect the fuel pressure regulator from the fuel delivery pipe.

      NOTICE:
      Do not disconnect the No. 2 fuel pipe from the fuel pressure regulator.



    5. A273743E01
    6. Connect SST to the fuel pipe.

      SST
      09268-31014   (09268-41500)
      Text in Illustration 
      *1
      SST (Fuel Tube Connector)
      *2
      Fuel Pipe

      CAUTION:
      Always read the precautions before connecting the fuel tube connector.



    7. A273849E01
    8. Connect SST (hose) to the fuel inlet of the pressure regulator with SST (union) and the 2 bolts.

      SST
      09268-31014   (09268-41091, 95336-08070)

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

      Text in Illustration 
      *1
      Fuel Pressure Regulator
      *2
      SST (Hose)
      *3
      No. 2 Fuel Pipe Sub-assembly
      *4
      SST (Union)

    9. Connect the fuel return hose to the fuel outlet of the pressure regulator.



    10. A273850E01
    11. Install a new O-ring to the injector.

    12. Connect SST (adapter and hose) to the injector and hold the injector and adapter with SST (clamp).

      SST
      09268-31014   (09268-41141, 09268-41410, 09268-41700, 95336-08070)
      Text in Illustration 
      *1
      SST (Hose)
      *2
      SST (Hose Band)
      *3
      O-Ring
      *4
      SST (Adapter)
      *5
      Vinyl Tube
      *6
      SST (Clamp)



    13. A273852E01
    14. Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

      SST
      09268-31014   (09268-41800)
      Text in Illustration 
      *1
      SST (Tie Band)
      *a
      Lock

      NOTICE:
      1. As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.
      2. Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.

      HINT:
      When removing SST (tie band), disengage the lock.

    15. Check that SST (clamp) and SST (adapter) cannot be easily separated.

    16. Put the injector into a graduated cylinder.

      CAUTION:
      Install a suitable vinyl tube to the injector to contain any gasoline spray.

    17. Connect the Techstream to the DLC3.

    18. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    19. Turn the Techstream on.

    20. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.



    21. A273851E01
    22. Connect SST (wire) to the injector and battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

      SST
      09842-30080  

      Standard injection volume:
      95 to 115 cm3 (5.8 to 7.0 cu. in.) per 15 seconds

      Difference between each injector:
      20 cm3 (1.2 cu. in.) or less

      Text in Illustration 
      *1
      SST (Wire)
      V100135
      Connect

      NOTICE:
      1. Make sure that SST (EFI inspection wire H) is securely connected.
      1. Always turn the voltage on and off on the battery side, not the fuel pump side.

      If the result is not as specified, replace the injector assembly.

  1. Check for fuel leakage.

    1. In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from the injector.

      Standard fuel leakage:
      1 drop or less every 16 minutes

      If the fuel leakage is not as specified, replace the injector assembly.