POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function) > Rear Power Window RH does not Operate with Rear Power Window Switch RH |

| 1.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - BATTERY) |
![]() |
Disconnect the O5 switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O5-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
![]() |
Remove the rear switch RH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 4 (U) - 3 (B) | UP | Below 1 Ω |
| 1 (D) - 2 (SD) | ||
| 4 (U) - 5 (SU) | OFF | Below 1 Ω |
| 1 (D) - 2 (SD) | ||
| 4 (U) - 5 (SU) | DOWN | Below 1 Ω |
| 1 (D) - 3 (B) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - REAR MOTOR RH) |

Disconnect the O5 switch connector.
Disconnect the O3 motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O5-1 (D) - O3-2 | Always | Below 1 Ω |
| O5-4 (U) - O3-1 | Always | Below 1 Ω |
| O5-1 (D) or O3-2 - Body ground | Always | 10 kΩ or higher |
| O5-4 (U) or O3-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| O5-1 (D) - O3-1 | Always | Below 1 Ω |
| O5-4 (U) - O3-2 | Always | Below 1 Ω |
| O5-1 (D) or O3-1 - Body ground | Always | 10 kΩ or higher |
| O5-4 (U) or O3-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH |
![]() |
Remove the rear motor RH (Click here).
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates counterclockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates clockwise |
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates clockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates counterclockwise |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH RH) |

Disconnect the N2 master switch connector.
Disconnect the O5 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N2-10 (U) - O5-5 (SU) | Always | Below 1 Ω |
| N2-18 (D) - O5-2 (SD) | Always | Below 1 Ω |
| N2-10 (U) or O5-5 (SU) - Body ground | Always | 10 kΩ or higher |
| N2-18 (D) or O5-2 (SD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
![]() |
Remove the master switch (Click here).
Reconnect the master switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N2-10 (U) - N2-1 (E) | Ignition switch ON, rear RH switch of master switch OFF → UP | Below 1 V → 11 to 14 V |
| N2-18 (D) - N2-1 (E) | Ignition switch ON, rear RH switch of master switch OFF → DOWN |
|
| ||||
| OK | ||
| ||