Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function) > Rear Power Window LH does not Operate with Rear Power Window Switch LH

for Preparation Click here


DESCRIPTION

HINT:
for Double Cab, CrewMax

  1. If the rear LH side manual UP/DOWN function does not operate, there may be a malfunction in the rear switch LH, rear motor LH, master switch or harness and connector.

WIRING DIAGRAM


B173121E04


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR SWITCH LH - BATTERY)
B149730E12
  1. Disconnect the O11 switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O11-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
B166135E02
  1. Remove the rear switch LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (U) - 3 (B)
    UP
    Below 1 Ω
    1 (D) - 2 (SD)
    4 (U) - 5 (SU)
    OFF
    Below 1 Ω
    1 (D) - 2 (SD)
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR SWITCH LH - REAR MOTOR LH)

B173122E02

  1. Disconnect the O11 switch connector.

  1. Disconnect the O9 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Double Cab: 
    Tester Connection
    Condition
    Specified Condition
    O11-1 (D) - O9-2
    Always
    Below 1 Ω
    O11-4 (U) - O9-1
    Always
    Below 1 Ω
    O11-1 (D) or O9-2 - Body ground
    Always
    10 kΩ or higher
    O11-4 (U) or O9-1 - Body ground
    Always
    10 kΩ or higher
    for CrewMax: 
    Tester Connection
    Condition
    Specified Condition
    O11-1 (D) - O9-1
    Always
    Below 1 Ω
    O11-4 (U) - O9-2
    Always
    Below 1 Ω
    O11-1 (D) or O9-1 - Body ground
    Always
    10 kΩ or higher
    O11-4 (U) or O9-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
B231474E04
  1. Remove the rear motor LH (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    for Double Cab: 
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise
    for CrewMax: 
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise



NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH LH)

B173123E02

  1. Disconnect the N2 master switch connector.

  1. Disconnect the O11 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-12 (U) - O11-5 (SU)
    Always
    Below 1 Ω
    N2-13 (D) - O11-2 (SD)
    N2-12 (U) or O11-5 (SU) - Body ground
    Always
    10 kΩ or higher
    N2-13 (D) or O11-2 (SD) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
B166136E05
  1. Remove the master switch (Click here).

  1. Reconnect the master switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N2-12 (U) - N2-1 (E)
    Ignition switch ON, rear LH switch of master switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-13 (D) - N2-1 (E)
    Ignition switch ON, rear LH switch of master switch OFF → DOWN



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL (Click here)