DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1) |
DTC P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) |
DTC P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
DTC P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) |
DTC P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2237 P2240 | Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2 trip detection logic) |
|
| P2238 P2241 |
(2 trip detection logic): (a) A1A+/A2A+ voltage 0.5 V or less (b) (A1A+/A2A+) - (A1A-/A2A-) = 0.1 V or less
(2 trip detection logic) |
|
| P2239 P2242 | A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| P2252 P2255 | A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic) |
|
| P2253 P2256 | A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| Related DTCs | P2237: A/F sensor (for Bank 1) open circuit between A1A+/A2A+ and A1A-/A2A- P2238: A/F sensor (for Bank 1) short circuit between A1A+/A2A+ and A1A-/A2A- P2238: A/F sensor (for Bank 1) short circuit between A1A+/A2A+ and GND P2238: A/F sensor (for Bank 1) low impedance P2239: A/F sensor (for Bank 1) short circuit between A1A+/A2A+ and +B P2240: A/F sensor (for Bank 2) open circuit between A1A+/A2A+ and A1A-/A2A- P2241: A/F sensor (for Bank 2) short circuit between A1A+/A2A+ and A1A-/A2A- P2241: A/F sensor (for Bank 2) short circuit between A1A+/A2A+ and GND P2241: A/F sensor (for Bank 1) low impedance P2242: A/F sensor (for Bank 2) short circuit between A1A+/A2A+ and +B P2252: A/F sensor (for Bank 1) short circuit between A1A-/A2A- and GND P2253: A/F sensor (for Bank 1) short circuit between A1A-/A2A- and +B P2255: A/F sensor (for Bank 2) short circuit between A1A-/A2A- and GND P2256: A/F sensor (for Bank 2) short circuit between A1A-/A2A- and +B |
| Required Sensors/Components (Main) | A/F sensor |
| Required Sensors/Components (Related) | Engine Coolant Temperature (ECT) sensor, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 10 seconds: A/F sensor open circuit between A1A+/A2A+ and A1A-/A2A- and Low impedance 5 seconds: Other |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P006A, P0107, P0108 (Manifold absolute pressure) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P0401 (EGR system) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control) P0451, P0452, P0453 (EVAP system) P0500, P0722 (Vehicle speed sensor) P0505 (IAC valve) P1340 (Camshaft position sensor) P2440 - P2447 (Secondary air injection system) |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 11 V or more |
| Engine | Running |
| Estimated sensor temperature | 450 to 550°C (842 to 1022°F) for P2237 and P2240 |
| Ignition switch | ON |
| Time after Ignition switch is OFF to ON | 5 seconds or more |
| Engine coolant temperature | 0°C (32°F) or higher |
| Estimated sensor temperature | 700 to 800°C (1292 to 1472°F) for P2238 and P2241 |
| Fuel cut | Not executed |
| Battery voltage | 11 V or higher |
| Ignition switch | ON |
| Timing after ignition switch off to ON | 5 seconds or more |
| A/F sensor admittance | Less than 0.002 1/Ω |
| A/F sensor admittance | Less than 0.0074 1/Ω |
| A1A+/A2A+ terminal voltage | 0.5 V or less |
| A1A+/A2A+ terminal voltage | More than 4.5 V |
| A1A-/A2A- terminal voltage | 0.5 V or less |
| A1A-/A2A- terminal voltage | More than 4.5 V |
| Difference between A1A+ and A1A-/A2A+ and A2A- terminal voltage | 0.1 V or less |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A/F sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D33-1 (HA1A) - D74-22 (HA1A) | Always | Below 1 Ω |
| D33-3 (A1A+) - D74-126 (A1A+) | Always | Below 1 Ω |
| D33-4 (A1A-) - D74-125 (A1A-) | Always | Below 1 Ω |
| D34-1 (HA2A) - D74-20 (HA2A) | Always | Below 1 Ω |
| D34-3 (A2A+) - D74-103 (A2A+) | Always | Below 1 Ω |
| D34-4 (A2A-) - D74-102 (A2A-) | Always | Below 1 Ω |
| D33-1 (HA1A) or D74-22 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D33-3 (A1A+) or D74-126 (A1A+) - Body ground | Always | 10 kΩ or higher |
| D33-4 (A1A-) or D74-125 (A1A-) - Body ground | Always | 10 kΩ or higher |
| D34-1 (HA2A) or D74-20 (HA2A) - Body ground | Always | 10 kΩ or higher |
| D34-3 (A2A+) or D74-103 (A2A+) - Body ground | Always | 10 kΩ or higher |
| D34-4 (A2A-) or D74-102 (A2A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 3.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output | B |
|
| ||||
| A | ||
| ||