Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0365    Camshaft Position Sensor "B" Circuit (Bank 1)

DTC    P0367    Camshaft Position Sensor "B" Circuit Low Input (Bank 1)

DTC    P0368    Camshaft Position Sensor "B" Circuit High Input (Bank 1)

DTC    P0390    Camshaft Position Sensor "B" Circuit (Bank 2)

DTC    P0392    Camshaft Position Sensor "B" Circuit Low Input (Bank 2)

DTC    P0393    Camshaft Position Sensor "B" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor (EV1, EV2 signal) consists of a magnet and MRE (Magnetoresistive Element).
The exhaust camshaft has 3 teeth on its outer circumference.
When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends the camshaft angle data to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0365
P0390
There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust side) circuit
  2. VVT sensor (for exhaust side)
  3. Exhaust camshaft
  4. Timing chain has jumped tooth
  5. ECM
P0367
P0392
Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust side) circuit
  2. VVT sensor (for exhaust side)
  3. Exhaust camshaft
  4. Timing chain has jumped tooth
  5. ECM
P0368
P0393
Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust side) circuit
  2. VVT sensor (for exhaust side)
  3. Exhaust camshaft
  4. Timing chain has jumped tooth
  5. ECM

  1. A228079E01
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveforms are as shown.
    2. EV1 and EV2 are the VVT sensor signal, and NE is the crankshaft position sensor signal.
      Item
      Content
      Terminal
      NE+ - NE-
      EV1+ - EV1-
      EV2+ - EV2-
      Equipment Setting
      5 V/DIV.
      20 msec./DIV.
      Condition
      Cranking or idling


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the VVT sensor.

MONITOR STRATEGY


Related DTCs
P0365: VVT sensor (bank 1) verify pulse input
P0367: VVT sensor (bank 1) range check (low voltage)
P0368: VVT sensor (bank 1) range check (high voltage)
P0390: VVT sensor (bank 2) verify pulse input
P0392: VVT sensor (bank 2) range check (low voltage)
P0393: VVT sensor (bank 2) range check (high voltage)
Required Sensors/Components (Main)
VVT sensor (for exhaust side)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
4 seconds: P0367, P0368, P0392 and P0393
5 seconds: P0365 and P0390
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0365, P0390 VVT Sensor Verify Pulse Input 
Monitor runs whenever following DTCs are not stored
P0367, P0368, P0392, P0393 (VVT sensor (for exhaust side))
Engine speed
600 rpm or more
Battery voltage
8 V or higher
Starter
OFF
Ignition switch
ON
VVT sensor voltage
0.3 to 4.7 V

P0367, P0368, P0392, P0393 VVT Sensor Range Check (Low Voltage, High Voltage) 
Monitor runs whenever following DTCs are not stored
P0365, P0390 (Exhaust VVT Sensor)
Starter
OFF
Ignition switch
ON
Time after ignition switch is turned from off to ON
2 seconds or more
Battery voltage
8 V or higher

TYPICAL MALFUNCTION THRESHOLDS


P0365, P0390 VVT Sensor Verify Pulse Input 
Exhaust VVT sensor signal
No signal

P0367, P0392 VVT Sensor Range Check (Low Voltage) 
Exhaust VVT sensor voltage
Below 0.3 V

P0368, P0393 VVT Sensor Range Check (High Voltage) 
Exhaust VVT sensor voltage
Higher than 4.7 V

COMPONENT OPERATING RANGE


VVT sensor voltage
0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0365, P0367, P0368, P0390, P0392 or P0393.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A160377E10


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR EXHAUST SIDE))


    A208648E24
  1. Disconnect the VVT sensor (for exhaust side) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D40-3 (VC2) - Body ground
    Ignition switch ON
    4.5 to 5.0 V
    D41-3 (VC2) - Body ground
    Ignition switch ON
    4.5 to 5.0 V

    Text in Illustration 
    *A
    for Bank 1
    *B
    for Bank 2
    *a
    Front view of wire harness connector
    (to VVT Sensor)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST SIDE) - ECM)
  1. Disconnect the VVT sensor (for exhaust side) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D40-1 (EX+) - D74-69 (EV1+)
    Always
    Below 1 Ω
    D40-2 (EX-) - D74-68 (EV1-)
    Always
    Below 1 Ω
    D41-1 (EX+) - D74-64 (EV2+)
    Always
    Below 1 Ω
    D41-2 (EX-) - D74-65 (EV2-)
    Always
    Below 1 Ω
    D40-1 (EX+) or D74-69 (EV1+) - Body ground
    Always
    10 kΩ or higher
    D40-2 (EX-) or D74-68 (EV1-) - Body ground
    Always
    10 kΩ or higher
    D41-1 (EX+) or D74-64 (EV2+) - Body ground
    Always
    10 kΩ or higher
    D41-2 (EX-) or D74-65 (EV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR EXHAUST SIDE))


    BR03795E18
  1. Check the VVT sensor (for exhaust side) installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
  1. Check the timing rotor of the exhaust camshaft.

OK:
Camshaft timing rotor does not have any cracks or deformation.

HINT:
Perform "Inspection After Repair" after replacing the exhaust camshaft (Click here).



NG
REPLACE EXHAUST CAMSHAFT (Click here)
OK


5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


    A103826E11
  1. Remove the cylinder head cover RH and LH.

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark

  1. Reinstall the cylinder head cover RH and LH.



NG
ADJUST VALVE TIMING
OK


6.REPLACE VVT SENSOR (FOR EXHAUST SIDE)
  1. Replace the VVT sensor (for exhaust side) (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Refer to the confirmation driving pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0365, P0367, P0368, P0390, P0392 or P0393 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END