Home › ENGINE · 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2444    Secondary Air Injection System Pump Stuck On Bank1

DTC    P2445    Secondary Air Injection System Pump Stuck Off Bank1

DTC    P2446    Secondary Air Injection System Pump Stuck On Bank 2

DTC    P2447    Secondary Air Injection System Pump Stuck Off Bank 2

for Preparation Click here


DESCRIPTION

Refer to P2440 .

DTC No.
DTC Detection Condition
Trouble Area
P2444
P2446
Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off
(2 trip detection logic)
  1. Short in air pump circuit
  2. Open or short in pressure sensor circuit
  3. Pressure sensor
  4. Air Injection Control Driver (AID)
  5. ECM
P2445
P2447
Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on
(2 trip detection logic)
  1. Air pump
  2. Open in air pump circuit
  3. Air injection system piping
  4. Vacuum hose (pressure sensor - air switching valve)
  5. Pressure sensor
  6. Open or short in pressure sensor circuit
  7. Air Injection Control Driver (AID)
  8. ECM
  9. Open or short in air pump heater circuit
  10. Air pump heater relay (AI HTR)

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the Air Switching Valve (ASV) of the Secondary Air Injection (AIR) system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the AIR system, and illuminates the MIL and stores a DTC:
  1. The pressure indicated by the pressure sensor does not reach threshold levels despite the ECM turning on the air pump.
  2. The pressure indicated by the pressure sensor exceeds threshold levels despite the ECM turning off the air pump.

MONITOR STRATEGY


Related DTCs
P2444: Air pump stuck ON
P2445: Air pump stuck OFF
P2446: Air pump stuck ON
P2447: Air pump stuck OFF
Required Sensors/Components (Main)
Pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per drive cycle
Duration
7 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not stored
P0010, P0020 (VVT Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air Fuel Ratio Sensor Heater)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT Sensor)
P0351 - P0358 (Igniter)
P0451, P0452, P0453 (EVAP System)
P0500, P0722 (Vehicle Speed Sensor)
P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation)
P2431, P2432, P2433, P2436, P2437, P2438 (Secondary Air Injection System Pressure Sensor)

P2444, P2446 (AIR pump is stuck on), P2445, P2447 (AIR pump is stuck off) 
Battery voltage
11 V or higher
Atmospheric pressure
45 kPa (337.5 mmHg) or more
Engine
Running
AIR monitor during AIR: ON*1
Completed
AIR monitor during AIR: OFF*2
Completed
Air injection Driver (open/short or out of range)
Not detected
AIR pressure sensor (open/short or out of range)
Not detected

*1: AIR monitor during AIR: ON 
Time after AIR in operation
5 seconds or more
AIR pump
ON
AIR valve
Open
Engine speed
400 to 3550 rpm
Intake air amount
Less than 99 g/s/L
Time after engine start
1 second or more

*2: AIR monitor during AIR: OFF 
Time after AIR in operation
10 seconds or more
AIR pump
OFF
AIR valve
Closed
Engine speed
Less than 2800 rpm
AIR monitor during AIR: ON
Completed
Engine load
4.5 to 55%
Time after engine started
1 second or more

P2445, P2447 (Secondary Air Injection Insufficient) 
Battery voltage
11 V or higher
Atmospheric pressure
45 kPa (337.5 mmHg) or more
Engine
Running
AIR monitor during AIR: ON*3
Completed
Air injection Driver (open/short or out of range)
Not detected
AIR pressure sensor (open/short or out of range)
Not detected

*3: AIR monitor during AIR: ON 
Time after AIR in operation
1 second or more
AIR valve
Open

TYPICAL MALFUNCTION THRESHOLDS


P2444, P2446 (AIR pump is stuck on) 
Either condition is met
(a) or (b)
(a) Secondary Air Injection OFF (Condition 1) is met
-
(b) Secondary Air Injection OFF (Condition 3) is met
-

P2445, P2447 (AIR pump is stuck off) 
Either condition is met
(a) or (b)
(a) Secondary Air Injection ON (Condition 2) is met
-
(b) Secondary Air Injection ON (Condition 4) is met
-

P2445, P2447 (Secondary Air Injection Insufficient) 
Cumulative pressure pulsation
(a) or (b)
(a) Air flow value at Bank 1 or Bank 2
140 L/min or less
(b) Air flow value at Bank 1 and Bank 2
140 L/min or less

Secondary Air Injection ON (Condition 1) 
Following conditions are met during AIR ON
-
Cumulative pressure pulsation
10 kPa or higher
AIR pressure
2.4 kPa or higher

Secondary Air Injection ON (Condition 2) 
Following conditions are met during AIR ON
-
Cumulative pressure pulsation
10 kPa or higher
AIR pressure
Below 2.4 kPa

Secondary Air Injection ON (Condition 3) 
Following conditions are met during AIR ON
-
Cumulative pressure pulsation
Below 10 kPa
AIR pressure
2.4 kPa or higher

Secondary Air Injection ON (Condition 4) 
Following conditions are met during AIR ON
-
Cumulative pressure pulsation
Below 10 kPa
AIR pressure
Below 2.4 kPa

Secondary Air Injection OFF (Condition 1) 
Following conditions are met during AIR OFF
-
Cumulative pressure pulsation
30 kPa or higher
AIR pressure
2.4 kPa or higher

Secondary Air Injection OFF (Condition 2) 
Following conditions are met during AIR OFF
-
Cumulative pressure pulsation
30 kPa or higher
AIR pressure
Below 2.4 kPa

Secondary Air Injection OFF (Condition 3) 
Following conditions are met during AIR OFF
-
Cumulative pressure pulsation
Below 30 kPa
AIR pressure
2.4 kPa or higher

Secondary Air Injection OFF (Condition 4) 
Following conditions are met during AIR OFF
-
Cumulative pressure pulsation
Below 30 kPa
AIR pressure
Below 2.4 kPa

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A199319E04

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
    Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
    While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
    If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear DTCs (if output) (Click here).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on [A].
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing ENTER (Next).
  12. Perform the following to confirm the AIR system pending codes: Press the ENTER (Exit).
  13. Check for pending DTCs [B].

    OK:
    No pending DTC is output.

  14. After the "Secondary Air Injection Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P2444, P2445, P2446 or P2447.
  16. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  18. Turn the ignition switch off.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Determination by ECM monitoring:
The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and stores a DTC. Soon after cold engine starts, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are AIR system pressure conditions in the AIR system passage.


Pressure Condition in Secondary Air Injection System Case 1: 
Air Pump
ON
Air Switching Valve
Open
Pressure
2.4 kPa or more
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2: 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 2.4 kPa
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3: 
Air Pump
ON
Air Switching Valve
Closed
Pressure
2.4 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4: 
Air Pump
OFF
Air Switching Valve
Close
Pressure
Less than 2.4 kPa
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5: 
Air Pump
ON
Air Switching Valve
Open
Pressure
2.4 kPa or more
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6: 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 2.4 kPa
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7: 
Air Pump
ON
Air Switching Valve
Closed
Pressure
2.4 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8: 
Air Pump
OFF
Air Switching Valve
Close
Pressure
Less than 2.4 kPa
Pulsation Detection
Exhaust gas pulsation not detected
If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.

HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

HINT:
  1. In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 10 to 30 kPa).
  2. In case 1, the average pressure is approximately 3 to 11 kPa. The value of 2.4 kPa indicated in the table above is a threshold for detecting pump malfunctions.


Detected Conditions while AIR operating:
Air pump ON, ASV Open
Detected Conditions while AIR not operating:
Air pump OFF, ASV Closed
ECM Determination
DTCs Output
Case 1
Case 8
Normal
-
Case 1
Case 6
ASV stuck open
P2440
or
P2442
Case 1
Case 7
Air pump stuck ON
P2444
or
P2446
Case 2
Case 8
Air pump stuck OFF
P2445
or
P2447
Case 3
Case 8
ASV stuck closed
P2441
or
P2443
Case 1
Case 5
ASV stuck open and air pump stuck ON
P2440 and P2444
or
P2442 and P2446
Case 2
Case 6
ASV stuck open and air pump stuck OFF
P2440 and P2445
or
P2442 and P2447
Case 3
Case 7
ASV stuck closed and air pump stuck ON
P2441 and P2444
or
P2443 and P2446
Case 4
Case 8
ASV stuck closed and air pump stuck OFF
P2441 and P2445
or
P2443 and P2447

HINT:
  1. If the vacuum hose between the ASV and the pressure sensor is not connected correctly, case 4 may occur.
  2. By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
  3. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  5. Bank 2 refers to the bank that does not include the No. 1 cylinder.

  1. System Check:
  2. The pressure in the secondary air passage can be checked using the Techstream.
    1. Start the engine and warm it up.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON and turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    6. Start the engine.
    7. Perform the AIR system intrusive operation while the engine is idling.
    8. Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.

      Standard:

      Operation
      AIR PUMP
      ASV
      PRESSURE*1
      PULSATION*2
      AIR PUMP: ON, ASV: OPEN
      ON
      OPEN
      2.4 kPa or more
      10 kPa or more
      AIR PUMP: OFF, ASV: CLOSE
      OFF
      CLOSE
      Less than 2.4 kPa
      Less than 30 kPa

      *1:
      Average pumping pressure (gauge pressure). The pressure should be 2.4 kPa or more when the AIR system operates.
      *2:
      The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
    9. Turn the ignition switch off.

      NOTICE:
      1. This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
        Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
        While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
        If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444, P2445, P2446 AND/OR P2447)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P2444, P2445, P2446 and/or P2447 are output
    A
    P2444, P2445, P2446 and/or P2447 and P0418 and/or P0419 are output
    B
    P2444, P2445, P2446 and/or P2447 and other DTCs (except P0418 and P0419) are output
    C
    If any DTCs other than P0418, P0419, P2444, P2445, P2446 and/or P2447 are output, troubleshoot those DTCs first.



B
GO TO AIR PUMP INSPECTION PROCEDURE

C
GO TO DTC CHART (Click here)
A


2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE AND AIR SWITCHING VALVE FREEZE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Read the values of Air Pump Freeze, Air Pump2 Freeze, Air Switching Valve Freeze and Air Switching Valve2 Freeze from the freeze frame data recorded previously.

  1. Referring to the following table, proceed to the appropriate step according to the result of the data reading.

    Result 
    Result
    Proceed to
    Air Pump Freeze
    Air Pump2 Freeze
    Air Switching Valve Freeze
    Air Switching Valve2 Freeze
    OFF
    OFF
    OFF
    OFF
    B
    Except above
    A



B
Go to step 8
A


3.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMP HEATER)


    A258728E01
  1. Disconnect the air pump connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.

  1. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Condition
    Specified Condition
    D89-1 - Body ground
    Activate the Air Pump Heater is ON
    11 to 14 V
    D90-1 - Body ground
    Activate the Air Pump Heater is ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Pump)



NG
Go to step 5
OK


4.INSPECT AIR PUMP (HEATER RESISTANCE)
  1. Inspect the air pump (Click here).



NG
REPLACE AIR PUMP
OK


5.INSPECT AIR PUMP HEATER RELAY (AI HTR)
  1. Inspect the air pump heater relay (AI HTR) (Click here).



NG
REPLACE AIR PUMP HEATER RELAY (AI HTR)
OK


6.CHECK AIR PUMP HEATER RELAY (AI HTR) (POWER SOURCE)
  1. Remove the air pump heater relay (AI HTR).



    A258729E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    AI HTR relay terminal 3 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (AIR PUMP - AI HTR RELAY, BODY GROUND)
  1. Remove the air pump heater relay (AI HTR).

  1. Disconnect the air pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    AI HTR relay terminal 5 - D89-1 (APH+)
    Always
    Below 1 Ω
    AI HTR relay terminal 5 - D90-1 (APH+)
    Always
    Below 1 Ω
    D89-3 (APHG) - Body ground
    Always
    Below 1 Ω
    D90-3 (APHG) - Body ground
    Always
    Below 1 Ω
    AI HTR relay terminal 5 or D89-1 (APH+) - Body ground
    Always
    10 kΩ or higher
    AI HTR relay terminal 5 or D90-1 (APH+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the AIR system intrusive operation while the engine is idling.

  1. Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) status displayed on the Techstream indicate the conditions shown in the table below.

    Standard:

    Operation
    AIR PUMP
    ASV
    PRESSURE*
    AIR PUMP: ON, ASV: OPEN
    ON
    ON
    2.4 kPa or more
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    OFF
    Less than 2.4 kPa

    *: Average pumping pressure. The pressure should be 2.4 kPa or more when the AIR system operates.

  1. Turn the ignition switch off.

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
      Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
      While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
      If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 10
OK


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2247)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (if output) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Result 
    Result
    Proceed to
    P2444, P2445, P2446 and/or P2447 are output
    A
    No pending DTC is output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


10.CHECK VACUUM HOSES (PRESSURE SENSOR - AIR SWITCHING VALVE)
  1. Check the vacuum hose connections with the pressure sensor and ASV.

  1. Inspect the vacuum hose for blockages and damage.

    OK:
    Vacuum hose has no blockages or damage.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


11.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR)
A165753E01
  1. Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).

  1. Check that the pressure displayed on the Techstream fluctuates when applying the pressure to the pressure sensor with the pressure gauge.

    NOTICE:
    Do not let foreign matter enter the sensor when applying pressure.

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The Techstream displays the air pump pressure as absolute pressure.



NG
REPLACE AIR SWITCHING VALVE (Click here)
OK


12.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS

A165786

  1. Check that all the pipes and hoses between the air pump and ASV are securely connected.

  1. Inspect the pipes and hoses for blockages and damage.

    OK:
    AIR system piping has no blockages or damage.



NG
REPAIR OR REPLACE AIR INJECTION SYSTEM PIPING
OK


13.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
A162305E08
  1. Disconnect the D48 and D50 or D52 and D54 AID connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D50-1 (E) - Body ground
    Always
    Below 1 Ω
    D54-1 (E2) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D48-1 (BATT) - Body ground
    Always
    11 to 14 V (near battery voltage)
    D50-5 (+B) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)
    D52-1 (BAT2) - Body ground
    Always
    11 to 14 V (near battery voltage)
    D54-5 (+B2) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)



NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK


14.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the D74 ECM connector.

  1. Disconnect the D50 or D54 AID connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    D74-54 (AIRP) - D50-4 (SIP)
    Always
    Below 1 Ω
    D74-53 (ARP2) - D54-4 (SIP2)
    Always
    Below 1 Ω
    D74-54 (AIRP) or D50-4 (SIP) - body ground
    Always
    10 kΩ or higher
    D74-53 (ARP2) or D54-4 (SIP2) - body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.INSPECT AIR PUMP


    A217481E01
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the 400 A probe of an ammeter to the positive (+) wire of the air pump.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Measure the current while the air pump is on and off.

    Standard Current:

    Tester Operation
    Air Pump
    ASV
    Specified Condition
    AIR PUMP: ON, ASV: OPEN
    ON
    OPEN
    10 to 40 A
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    CLOSE
    Below 1 A

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
      Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
      While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
      If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



OK
Go to step 18

NG
Go to step 16

16.REPLACE AIR PUMP
  1. Replace the air pump (Click here).


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (if output) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Result 
    Result
    Proceed to
    No pending DTC is output
    A
    P2444, P2445, P2446 and/or P2447 are output
    B



B
Go to step 18
A

END 

18.PERFORM ACTIVE TEST USING TECHSTREAM


    A242126E04
  1. Disconnect the D50 or D54 AID connector.

  1. Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the AIR system forced operation while the engine is idling.

  1. Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    D50-3 (SIV) - D50-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    D54-3 (SIV2) - D54-1 (E2)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    D50-3 (SIV) - D50-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V
    D54-3 (SIV2) - D54-1 (E2)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



    A242126E05
  1. Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the AIR system forced operation while the engine is idling.

  1. Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    D50-4 (SIP) - D50-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    D54-4 (SIP2) - D54-1 (E2)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    D50-4 (SIP) - D50-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V
    D54-4 (SIP2) - D54-1 (E2)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


19.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


20.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (if output) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC is output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
REPLACE ECM
OK

END