WATER PUMP > INSTALLATION |
| 1. INSTALL WATER PUMP ASSEMBLY |
![]() |
Install a new gasket and the water pump with the 17 bolts.
| 2. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Temporarily install the V-ribbed belt tensioner with the 5 bolts.
| Item | Length |
| A | 70 mm (2.76 in.) |
| B | 33 mm (1.30 in.) |
![]() | Bolt A |
![]() | Bolt B |
Tighten bolts 1 and 2 in numerical order.
Tighten the other bolts.
| 3. CONNECT COOLER COMPRESSOR ASSEMBLY |
Install the cooler compressor with the 2 stud bolts.
![]() |
Install the 2 bolts and 2 nuts.
Connect the cooler compressor connector.
| 4. INSTALL GENERATOR ASSEMBLY |
| 5. CONNECT VANE PUMP ASSEMBLY |
Connect the vane pump with the 2 bolts.
Attach the wire harness clamp.
Connect the connector.
| 6. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY |
for Separate Type:
Install the 2 idler pulley cover plates, 2 No. 2 idler pulleys and 2 No. 2 idler pulley cover plates with the 2 bolts.
for Integrated Type:
Install the 2 No. 2 idler pulleys with the 2 bolts.
| 7. INSTALL WATER INLET HOUSING |
![]() |
Install a new O-ring to the water outlet pipe.
Install a new gasket to the water pump.
Apply soapy water to the gasket of the water outlet pipe.
Install the water inlet with the 5 bolts.
Connect the 5 water by-pass hoses.
Connect the No. 2 oil cooler hose.
Connect the oil cooler hose.
Connect the throttle body connector.
| 8. CONNECT AIR TUBE |
Connect the air tube with the 2 bolts.
| 9. INSTALL FAN SHROUD |
Install the fan pulley to the water pump.
Place the shroud together with the coupling fan between the radiator and engine.
![]() |
Align the paint marks on the heads of the water pump stud bolts with the paint marks of the same color on the outer edge of the fluid coupling flange and install the fluid coupling to the water pump.
| *1 | Paint Mark |
Temporarily install the fluid coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the claws of the shroud to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the radiator tank upper.
Install the fan and generator V-belt .
Tighten the 4 nuts of the fluid coupling fan.
| 10. INSTALL RADIATOR HOSE OUTLET |
![]() |
Connect the radiator hose outlet to the water inlet housing shown in the illustration.
| *a | Upper |
| *b | Front |
![]() |
Install the radiator hose outlet to the radiator shown in the illustration.
| *a | Upper |
| *b | RH |
| 11. INSTALL RADIATOR HOSE INLET |
![]() |
Connect the radiator hose inlet as shown in the illustration.
| *a | Upper |
| *b | LH |
| *c | Front |
| 12. ADD ENGINE COOLANT |
Add engine coolant.
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Install the radiator cap.*1
Start the engine and stop it immediately.*2
Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3
Repeat steps *1, *2 and *3 until the coolant level does not decrease.
Install the radiator cap.*4
Set the air conditioning as follows.*5
| Item | Condition |
| Fan speed | Any setting except off |
| Temperature | Toward WARM |
| Air conditioning switch | Off |
Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6
Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7
If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8
If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the FULL line.
If the coolant level is below the FULL line, repeat steps *4 through *8.
If the coolant level is above the FULL line, drain coolant until the coolant level reaches the FULL line.
| 13. INSPECT FOR COOLANT LEAK |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 14. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.