Home › MAINTENANCE › MAINTENANCE › CHASSIS

CHASSIS > GENERAL MAINTENANCE



1. INSPECT POWER STEERING FLUID (Except North America)
  1. Inspect the power steering fluid.
    Type
    See procedures
    1GR-FE
    Click here
    1UR-FE
    Click here
    3UR-FE
    Click here



2. INSPECT STEERING LINKAGE AND GEAR HOUSING
  1. Check the steering wheel free play (Click here).

  1. Check the steering linkage for looseness or damage.

    1. Check that the tie rod ends do not have excessive play.

    2. Check that the dust seals and boots are not damaged.

    3. Check that the boot clamps are not loose.

    4. Check that the steering gear housing is not damaged.

    5. Check that the connectors are properly connected to the steering gear housing.



3. INSPECT STEERING GEAR HOUSING OIL
  1. Check for steering gear housing oil leakage.
    If leakage is found, check and repair the cause.



4. INSPECT BALL JOINT AND DUST COVER
  1. Inspect the ball joints for excessive looseness.

    1. Jack up the front of the vehicle and place wooden blocks with a height of 180 to 200 mm (7.09 to 7.87 in.) under the front tires.

    2. Lower the vehicle until the front coil spring has about half its ordinary load. Place stands under the vehicle for safety.

    3. Check that the front wheels are pointing straight ahead. Use wheel chocks on all 4 wheels.

    4. Using a lever, pry up the end of the lower arm. Check the amount of play.

      Maximum ball joint vertical play:
      0 mm (0 in.)

      If there is any play, replace the ball joint.

  1. Check the dust cover for damage.



5. INSPECT DRIVE SHAFT BOOTS (for 4WD)
  1. Check the drive shaft boots for loose clamps, grease leakage, kinks or damage.



6. INSPECT AUTOMATIC TRANSMISSION FLUID
  1. Visually check the automatic transmission for fluid leakage. If fluid is leaking, find the cause and repair it.
    Type
    See procedures
    A750E
    Click here
    A760E
    Click here
    A760F
    Click here
    AB60F
    Click here
    AB60E
    Click here



7. REPLACE AUTOMATIC TRANSMISSION FLUID
  1. Replace the automatic transmission fluid.
    Type
    See procedures
    A750E
    Click here
    A760E
    Click here
    A760F
    Click here
    AB60F
    Click here
    AB60E
    Click here



8. INSPECT TRANSFER OIL (for 4WD)
  1. Inspect the transfer oil (Click here).



9. REPLACE TRANSFER OIL (for 4WD)
  1. Replace the transfer oil (Click here).



10. INSPECT FRONT DIFFERENTIAL OIL (for 4WD) AND REAR DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil type:
    Item
    Oil type and viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front differential capacity:
    Specified Condition
    2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.)


    Rear differential capacity:

    Engine type
    Wheelbase type
    Cab type
    Drive type
    Specified Condition
    3UR-FE. 3UR-FBE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    Regular
    2WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4WD
    Double
    2WD
    4WD
    CrewMax
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4180 mm (13 ft. 8.6 in.)
    Double
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    1GR-FE and 1UR-FE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    ALL
    2WD
    4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.)
    4WD
    4180 mm (13 ft. 8.6 in.)
    2WD
    4WD

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }



11. REPLACE FRONT DIFFERENTIAL OIL (for 4WD) AND REAR DIFFERENTIAL OIL
  1. Replace the front differential oil and rear differential oil (Click here).



12. LUBRICATE PROPELLER SHAFT AND TIGHTEN BOLTS


  1. for 4WD:
    Lubricate the propeller shaft by referring to the lubrication chart. Before pumping in grease, wipe off any mud and dust on the grease fitting.



    1. for Front propeller shaft


      C158565E01



    2. for Rear propeller shaft


      C158514E01



      C160963E01

  1. Tighten the bolts of the propeller shaft.
    Type
    See procedures
    Front propeller shaft
    Click here
    Rear propeller shaft (for 2WD)
    Click here
    Rear propeller shaft (for 4WD)
    Click here



13. INSPECT FRONT AND REAR SUSPENSION (Except North America)
Type
See procedures
Front
Click here
Rear
Click here


14. ROTATE TIRES


    C258067E01
  1. Rotate the tires as shown in the illustration.

    Torque:
    for Aluminum Wheel:
    131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
    for Steel Wheel:
    209 N*m{ 2131 kgf*cm , 154 ft.*lbf }

    Text in Illustration 
    *a
    Front of the Vehicle