Home › BRAKE › BRAKE › BRAKE PEDAL

BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL PAD
  1. Install the brake pedal pad onto the brake pedal.



2. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY


    C154462
  1. Install the brake pedal support with the 4 nuts.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

  1. Install the No. 3 brake pedal bracket to the brake pedal support.



    C208543
  1. Temporarily install the brake pedal support, No. 3 brake pedal bracket and brake pedal lever with the bolt and nut.



    C208544E01
  1. Install the bolt to the No. 3 brake pedal bracket.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Apply a light coat of lithium soap base glycol grease to the inner surface of the hole on the brake pedal and return spring mounting bracket of the No. 3 brake pedal bracket.

  1. Install the brake pedal return spring.

  1. Tighten the bolt and nut.

    Torque:
    23 N*m{ 239 kgf*cm , 17 ft.*lbf }



3. INSTALL PUSH ROD PIN
  1. Apply a light coat of lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.

  1. Set the push rod clevis in place, insert the push rod pin from outside the vehicle and then install a new clip.

    NOTICE:
    After assembly, check that the pedal operates smoothly.



4. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER
  1. Install the stop light switch mounting adjuster .



5. INSTALL STOP LIGHT SWITCH ASSEMBLY
  1. Attach the harness clip.

  1. Install the stop light switch .

  1. Connect the stop light switch connector.



6. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    C154523
  1. Install the air duct with the bolt.



7. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. for Automatic Air Conditioning System:
    Attach the 2 claws to install the sensor.



    B226740
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 bolts.

  1. Install the hood lock control lever.



9. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



10. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)


B165843
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



11. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)


B165841
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



12. CHECK AND ADJUST BRAKE PEDAL
  1. Check and adjust brake pedal (Click here).



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


14. CHECK MASTER CYLINDER PRESSURE SENSOR SIGNAL
  1. Check the sensor signal (Click here).