Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

DTC    B2311    Power Window Motor Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator motor is driven by operating the power window switch. The power window regulator sub-assembly consists of the motor, regulator and ECU.
This DTC is stored when the power window regulator motor has a malfunction, or the ECU built into the power window regulator motor determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

HINT:
DTC B2311 is set when the ECU for the front door power window regulator motor assembly LH or RH malfunctions.

NOTICE:
  1. When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
  2. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:
    1. Close the power window by fully pulling up the power window switch and holding it in the auto up position.
    2. Open the power window by fully pushing down the switch.


Driver Side Motor 
DTC Code
DTC Detection Condition
Trouble Area
B2311
  1. Either condition below is met:
    1. The power window regulator motor malfunctions.
    2. The ECU in the power window regulator motor determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.
  1. Battery disconnection when ignition switch ON
  2. Front power window regulator motor assembly LH
  3. Incorrect installation of power window components
  4. Overheated power window regulator motor

Front Passenger Side Motor 
DTC Code
DTC Detection Condition
Trouble Area
B2311
  1. Either condition below is met:
    1. The power window regulator motor malfunctions.
    2. The ECU in the power window regulator motor determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.
  1. Battery disconnection when ignition switch ON
  2. Front power window regulator motor assembly RH
  3. Incorrect installation of power window components
  4. Overheated power window regulator motor

INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (POWER WINDOW)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that each door window regulator operates (Click here).

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.


    D-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Driver side power window
    OFF/UP/DOWN
    -

    P-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Front passenger side power window
    OFF/UP/DOWN
    -

    OK:
    Each power window motor operates.

    Result 
    Result
    Proceed to
    OK
    A
    NG (Driver side power window)
    B
    NG (Front passenger side power window)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
A


2.PERFORM INITIALIZATION
  1. Initialize the power window regulator motor (Click here).

  1. Check that each power window operates normally by opening and closing each window (Click here).

    OK:
    Each power window operates normally.

    Result 
    Result
    Proceed to
    OK
    A
    NG (Driver side power window)
    B
    NG (Front passenger side power window)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
A


3.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
  1. Check that the power window components are installed correctly.

    OK:
    Power window components are installed correctly.

    HINT:
    When the power window components are installed correctly, the problem has been caused by battery disconnection while the ignition switch is ON or the motor being overheated.



NG
INSTALL PARTS CORRECTLY
OK

END