Home › ENGINE ยท 1GR-FE › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY
(Click here)


2. REMOVE EMISSION CONTROL VALVE SET


    A239079
  1. Disconnect the emission control valve set connector.

  1. Disconnect the air hose from the emission control valve set.



    A239080
  1. Remove the 3 nuts and emission control valve set.



3. REMOVE NO. 2 EMISSION CONTROL VALVE SET


    A239086
  1. Disconnect the No. 2 emission control valve set connector.

  1. Disconnect the air hose.



    A239087
  1. Remove the 3 nuts and No. 2 emission control valve set.



4. REMOVE IGNITION COIL ASSEMBLY


    A221430
  1. Disconnect the 6 ignition coil connectors.

  1. Remove the 6 bolts and 6 ignition coils.



5. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A243467
  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



6. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A223013
  1. Disconnect the 2 hoses.

  1. Remove the 3 bolts and water by-pass pipe.



7. REMOVE WATER INLET HOUSING


    A225380
  1. Disconnect the 3 water by-pass hoses.



    A223012
  1. Remove the 5 bolts and water inlet housing.



    A224736
  1. Remove the O-ring and gasket from the water outlet pipe and water pump.



    A225379
  1. Remove the 3 water by-pass hoses.



8. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A158544
  1. Remove the bolt and No. 1 idler pulley.



9. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


A223006E03
  1. for Separate Type:
    Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulleys and 2 No. 2 idler pulley cover plates.
    Text in Illustration 
    *A
    LH
    *B
    RH

  1. for Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulleys.



10. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A222180
  1. Remove the 5 bolts and V-ribbed belt tensioner.



11. REMOVE OIL FILTER ELEMENT


    A094910E09
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A222100
  1. Remove the oil filter drain plug.



    A222101E01
  1. Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A222102
  1. Check that oil is drained from the oil filter. Then, disconnect the pipe as shown in the illustration and remove the O-ring.



    A222103E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.



    A153538E03
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.



12. REMOVE OIL FILTER BRACKET


    A225410
  1. Remove the 2 nuts, bolt, oil filter bracket and gasket.



13. REMOVE CRANKSHAFT PULLEY


    A072947E04
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E02
  1. Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)



14. REMOVE NO. 1 OIL PIPE


    A223691
  1. Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



15. REMOVE NO. 2 OIL PIPE


    A223692
  1. Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



16. DISCONNECT FUEL PIPE SUB-ASSEMBLY
  1. Remove the 2 bolts and disconnect the fuel pipe.



17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A223666
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A223665
  1. Remove the 3 gaskets.



18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A223669
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A223668
  1. Remove the 3 gaskets.



19. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A174340
  1. Remove the 10 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A174341E02
  1. Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
    Text in Illustration 
    *1
    Oil Pan Seal Cutter

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.



20. REMOVE OIL STRAINER SUB-ASSEMBLY


    A239204
  1. Remove the 2 nuts, oil strainer and gasket.



21. REMOVE OIL PAN SUB-ASSEMBLY


    A222173
  1. Remove the 17 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A221168E04
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Pry

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.



    A222122
  1. Remove the 3 O-rings from the timing chain cover.



22. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A221169
  1. Remove the 26 bolts and the 2 nuts.



    A221170
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

    HINT:
    Tape the screwdriver tip before use.



    A221404
  1. Remove the oil pump gasket from the cylinder block.



23. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. Using a screwdriver and wooden block, pry out the oil seal.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.