Home › COMMUNICATION SYSTEM › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM

DTC    B2321    Driver Side Door ECU Communication Stop

for Preparation Click here


DESCRIPTION

This DTC is output when LIN communication between the front power window regulator motor assembly LH and main body ECU (driver side junction block) stops for 10 seconds or more.

DTC Code
DTC Detection Condition
Trouble Area
B2321
No communication between the front power window regulator motor assembly LH and main body ECU (driver side junction block) for 10 seconds or more.
  1. Front power window regulator motor assembly LH
  2. Main body ECU (driver side junction block)
  3. Harness or connector

WIRING DIAGRAM


E160670E03


INSPECTION PROCEDURE

NOTICE:
When using the Techstream with the ignition switch OFF to troubleshoot:
Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

HINT:
  1. DTC B2325 is output when communication between the front power window regulator motor assembly LH and main body ECU (driver side junction block) stops.
  2. When DTC B1206 and B2321 are output simultaneously, perform the troubleshooting for DTC B1206 first (Click here).

1.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2321 output reoccurs
    A
    DTC B2321 output does not reoccur
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REGULATOR MOTOR LH)


    E160671E03
  1. Disconnect the J2 main body ECU (driver side junction block) connector.

  1. Disconnect the N12 front power window regulator motor assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J2-10 (LIN2) - N12-9 (LIN)
    Always
    Below 1 Ω
    J2-10 (LIN2) or N12-9 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REGULATOR MOTOR LH - BATTERY AND BODY GROUND)


    E160672E05
  1. Disconnect the N12 front power window regulator motor assembly LH connector.

  1. Measure the resistance and voltage according to the value(s) in the tables below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N12-1 (GND) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    N12-2 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Temporarily replace the front power window regulator motor assembly LH with a new or normally functioning one (Click here).

  1. Clear the DTC (Click here).


NEXT


6.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2321 output does not reoccur
    A
    DTC B2321 output reoccurs
    B



B
REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)
A

END (FRONT POWER WINDOW REGULATOR MOTOR LH IS DEFECTIVE)