Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Rear Door Lock Motor Circuit

for Preparation Click here


DESCRIPTION

The main body ECU controls the rear door lock motor to lock/unlock the rear door. This ECU applies current from terminal ACT+ to terminal ACT- to operate the motor to lock the door. It reverses the direction of the current flow to operate the motor to unlock the door.

WIRING DIAGRAM


B264630E02


INSPECTION PROCEDURE

1.INSPECT REAR DOOR LOCK MOTOR ASSEMBLY
E147082E02
E147081E01
  1. Remove the rear door lock motor LH.

    1. for Double Cab: (Click here)
    2. for CrewMax: (Click here)

  1. Apply battery voltage and check operation of the door lock motor.

    OK:
    for Rear LH 
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 4 (L)
    Battery negative (-) → Terminal 1 (UL)
    Lock
    Battery positive (+) → Terminal 1 (UL)
    Battery negative (-) → Terminal 4 (L)
    Unlock

  1. Remove the rear door lock motor RH.

    1. for Double Cab: (Click here)
    2. for CrewMax: (Click here)

  1. Apply battery voltage and check operation of the door lock motor.

    OK:
    for Rear RH 
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 4 (L)
    Battery negative (-) → Terminal 1 (UL)
    Lock
    Battery positive (+) → Terminal 1 (UL)
    Battery negative (-) → Terminal 4 (L)
    Unlock

    Result 
    Result
    Proceed to
    OK (Rear door lock motor LH)
    A
    OK (Rear door lock motor RH)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
Go to step 3

C
REPLACE REAR DOOR LOCK MOTOR ASSEMBLY (Click here)

D
REPLACE REAR DOOR LOCK MOTOR ASSEMBLY (Click here)
A


2.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK MOTOR LH - MAIN BODY ECU)
E146546E03
  1. Disconnect the O10 door lock connector.

  1. Disconnect the DC ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O10-4 (L) - DC-24 (ACT+)
    Always
    Below 1 Ω
    O10-1 (UL) - DC-23 (ACT-)
    DC-24 (ACT+) - Body ground
    Always
    10 kΩ or higher
    DC-23 (ACT-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

3.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK MOTOR RH - MAIN BODY ECU)

E146616E05

  1. Disconnect the O4 door lock connector.

  1. Disconnect the DD ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-4 (L) - DD-3 (ACT+)
    Always
    Below 1 Ω
    O4-1 (UL) - DD-2 (ACT-)
    DD-3 (ACT+) - Body ground
    Always
    10 kΩ or higher
    DD-2 (ACT-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU