Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to GND in CAN Bus Line

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and GND when there is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.

Symptom
Trouble Area
There is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of DLC3.
  1. Short to GND
  2. Combination meter ECU
  3. Main body ECU
  4. Skid control ECU with actuator
  5. Steering angle sensor
  6. Center airbag sensor
  7. Bus buffer ECU*1
  8. Air conditioning amplifier
  9. ECM
  10. 4WD control ECU*2
  11. Power steering ECU*3
  12. No. 1 junction connector
  13. No. 2 junction connector

HINT:
  1. *1: w/ Bus Buffer ECU
  2. *2: w/ 4WD
  3. *3: w/ Power Steering ECU


WIRING DIAGRAM


C226558E02


C210579E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


NEXT


3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE)


    H102392E72
  1. Disconnect the J118 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J17-6 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J17-14 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4.CONNECT CONNECTOR
  1. Reconnect the J118 No. 1 junction connector.


NEXT


5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    H102392E72
  1. Disconnect the J113 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J17-6 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J17-14 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 14
OK


6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)


    C175162E41
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J113-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J113-12 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 10
OK


7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)

NOTICE:
For vehicles without a bus buffer ECU, go to "CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)".



    C175162E42
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J113-5 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J113-16 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 11
OK


8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without 4-wheel drive, go to "CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM)".



    C175162E43
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J113-2 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J113-13 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 12
OK


9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    C175162E44
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J113-3 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J113-14 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 13
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR 

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER)


    C175162E41
  1. Disconnect the J19 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J113-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J113-12 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY  

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BUS BUFFER ECU)


    C175162E42
  1. Disconnect the J59 bus buffer ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J113-5 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J113-16 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)
OK

REPLACE BUS BUFFER ECU 

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (4WD CONTROL ECU)


    C175162E43
  1. Disconnect the A25 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J113-2 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J113-13 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4WD CONTROL ECU  

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)


    C175162E44
  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J113-3 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J113-14 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher

    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1UR-FE)
    B
    OK (for 3UR-FE)
    C
    OK (for 3UR-FBE)
    D
    NG
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)  

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C226869E08
  1. Disconnect the J118 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-12 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


15.CONNECT CONNECTOR
  1. Reconnect the J113 No. 2 junction connector.


NEXT


16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C226869E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-4 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-15 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 22
OK


17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    C226869E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-5 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-16 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 23
OK


18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU WITH ACTUATOR)


    C226869E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-8 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-19 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 24
OK


19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C226869E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-6 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-17 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 25
OK


20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU)

NOTICE:
For vehicles without a power steering ECU, go to "CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)".



    C226869E13
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-7 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-18 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 26
OK


21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)


    C226869E14
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-3 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-14 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
Go to step 27
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR 

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ECU)


    C226869E09
  1. Disconnect the J28 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-4 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-15 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY  

23.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)


    C226869E10
  1. Disconnect the J2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-5 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-16 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU 

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU WITH ACTUATOR)


    C226869E11
  1. Disconnect the A17 skid control ECU with actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-8 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-19 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU WITH ACTUATOR (CANH, CANL)
OK

REPLACE SKID CONTROL ECU WITH ACTUATOR (Click here)  

25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    C226869E12
  1. Disconnect the J6 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-6 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-17 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR  

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU)


    C226869E13
  1. Disconnect the J119 power steering ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-7 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-18 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)
OK

REPLACE POWER STEERING ECU (Click here)  

27.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR)


    C226869E14
  1. Disconnect the J46 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J118-3 (CANH) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher
    J118-14 (CANL) - J17-4 (CG)
    Ignition switch OFF
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR